690574

Makita EM2653LHN Manual

5
Zoom out
Zoom in
Previous page
1/84
Next page
5
Start the brushcutter only in accordance with the instructions.
– Do not use any other methods for starting the engine!
– Usethebrushcutterandthetoolsonlyforsuchapplicationsasspecied.
– Only start the engine, after the entire assembly is done. Operation of the
device is only permitted after all the appropriate accessories are attached!
– Before starting make sure that the cutting tool has no contact with hard
objectssuchasbranches,stonesetc.asthecuttingtoolwillrevolvewhen
starting.
– The engine is to be switched off immediately in case of any engine problems.
– Shouldthecuttingtoolhitstonesorotherhardobjects,immediatelyswitchoff
the engine and inspect the cutting tool.
– Inspect the cutting tool at short regular intervals for damage (detection of
hairline cracks by means of tapping-noise test).
– If the equipment gets heavy impact or fall, check the condition before
continuing work. Check the fuel system for fuel leakage and the controls
and safety devices for malfunction. If there is any damage or doubt, ask our
authorizedservicecenterfortheinspectionandrepair.
– Operate the equipment only with the shoulder harness attached which is
tobesuitablyadjustedbeforeputtingthebrushcutterintooperation.Itis
essentialtoadjusttheshoulderharnessaccordingtotheusersizetoprevent
fatigue occurring during use. Never hold the cutter with one hand during use.
– During operation always hold the brushcutter with both hands.
Always ensure a safe footing.
– Operate the equipment in such a manner as to avoid inhalation of the exhaust
gases. Never run the engine in enclosed rooms (risk of gas poisoning).
Carbon monoxide is an odorless gas.
– Switch off the engine when resting and when leaving the equipment
unattended, and place it in a safe location to prevent danger to others or
damage to the machine.
– Never put the hot brushcutter onto dry grass or onto any combustible
materials.
– Always install the approved cutting tool guard onto the equipment before
starting the engine.
Otherwisecontactwiththecuttingtoolmaycauseseriousinjury.
– All protective installations and guards supplied with the machine must be
used during operation.
– Neveroperatetheenginewithfaultyexhaustmufer.
– Shut off the engine during transport.
– When transporting the equipment, always attach the cover to the cutting
blade.
– Ensure safe position of the equipment during car transportation to avoid fuel
leakage.
– When transporting, ensure that the fuel tank is completely empty.
– When unloading the equipment from the truck, never drop the Engine to the
ground or this may severely damage the fuel tank.
– Except in case of emergency, never drop or cast the equipment to the ground
or this may severely damage the equipment.
– Remember to lift the entire equipment from the ground when moving the
equipment. Dragging the fuel tank is highly dangerous and will cause damage
andleakageoffuel,possiblycausingre.
Refueling
– Shutofftheengineduringrefueling,keepawayfromopenamesanddonot
smoke.
– Avoid skin contact with mineral oil products. Do not inhale fuel vapor. Always
wear protective gloves during refueling. Change and clean protective clothing
at regular intervals.
– Take care not to spill either fuel or oil in order to prevent soil contamination
(environmental protection). Clean the brushcutter immediately after fuel has
been spilt.
– Avoid any fuel contact with your clothing. Change your clothing instantly if
fuelhasbeenspiltonit(topreventclothingcatchingre).
– Inspect the fuel cap at regular intervals making sure that it can be securely
fastened and does not leak.
– Carefully tighten the fuel tank cap. Change location to start the engine (at
least 3 meters away from the place of refueling).
– Never refuel in closed rooms. Fuel vapors accumulate at ground lever (risk of
explosions).
– Only transport and store fuel in approved containers. Make sure the fuel
stored is not accessible to children.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita EM2653LHN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita EM2653LHN in the language / languages: English, Portuguese, Spanish as an attachment in your email.

The manual is 17,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info