Manual Makita ELM3800 (page 9 of 19) (English, Dutch)

599886

Zoom out

Zoom in

1/19

38. Be careful during adjustment of the machine to

prevent entrapment of the fingers between moving

blades and fixed parts of the machine.

39. Always allow the machine to cool before storing.

40. When servicing the blades be aware that, even though

the power source is switched off, the blades can still

be moved.

41. Replace worn or damaged parts for safety; Use only

genuine replacement parts and accessories.

42. Be careful during adjustment of the appliance to

prevent entrapment of the fingers between moving

blades and fixed parts of appliance.

43. If the supply cord is damaged, it must be replaced by

the manufacturer, its service agent or similarly

qualified persons in order to avoid a hazard.

3. GENERAL IDENTIFICATION

(Fig. 1)

4. TECHNICAL DATA

5. ASSEMBLY

5-1 ASSEMBLE THE FOLDING HANDLE

A) Fix the lower handlebars into the unit body with

locking knobs. (Fig. 2A/Fig. 2B/Fig. 2C)

B) Connect the upper handle and the lower handle with

bolts, washers and locking knobs. (Fig. 2D/Fig. 2E/

Fig. 2F)

C) Attach the cable clamp to the position shown and then

attach the cable. (Fig. 2G/Fig. 2H)

5-2 ASSEMBLE THE GRASS CATCHER

1. To fit: Raise the rear cover and hitch the grass catcher

on rear of mower. (Fig. 3A/Fig. 3B/Fig. 3C)

2. To remove: Grasp and lift the rear cover, remove

grass catcher.

There is a level indicator on the top of the grass catcher

that shows whether the catcher is empty or full:

- If the catcher is full, the indicator collapses; once this

happens, stop moving immediately and empty the

catcher, make sure it is clean and ensure its meshwork

is ventilated. (Fig. 3D)

- The level indicator inflates if the catcher is not full

during the moving. (Fig. 3E)

IMPORTANT:

If the position of indicator opening is very dirty, the

indicator will not inflate-in this case, clean the position of

indicator opening immediately.

6. ADJUSTMENT OF CUTTING

HEIGHT

Apply outward pressure to disengage lever from rack.

Move lever forward or back to adjust height.

The height (the blade to the ground) can be adjusted from

25 mm (position 1) to 75 mm (position 6), 6 height

positions. All wheels will be in the same height of cut.

(Fig. 4A/Fig. 4B)

WARNING: Make this adjustment only when the

blade is stopped.

WARNING: Disconnect the electric cord from the

power supply.

7. SAFETY PRECAUTIONS

a) Always operate with the deflector or grass catcher in

the correct position.

b) Always stop the motor before removing the grass

catcher or adjusting the height of cutting position.

1. Before mowing, remove all foreign objects from the

lawn which may be thrown by the machine.

While mowing, stay alert for any foreign objects which

may have been missed. (Fig. 5A)

2. Never lift the rear of the mower while starting the

motor or during normal operation. (Fig. 5B)

3. Never place your hands or feet underneath the

underpan or into the rear discharge chute while the

motor is running. (Fig. 5C)

8. STARTING

8-1 STARTING

Before connecting up the lawn mower to the electric

power supply, make sure that the mains supply voltage is

230-240 V~ 50 Hz.

Before start the lawn mower, fix the extension cord with

the machine as the Fig. 6A shown.

Start the motor as follows. (Fig. 6B)

a) Press the safety push-button (1).

b) And meanwhile, pull the switch handle (2), and keep it

in grasp.

If you release the switch handle, the motor will stop.

Model ELM3800

Rated voltage 230-240 V~

Rated frequency 50 Hz

Rated power 1,400 W

No load speed

3,450 min

-1

Grass catcher capacity 40 L

Cutting width 380 mm

Net weight 13 kg

Degree of protection against

liquid

IP24

Height adjustment 25-75 mm, 6 adjustment

Model ELM3800

Sound pressure level at the

operator’s position

83 dB(A),

K=3 dB(A)

Measured sound power level 93.4 dB(A),

K=2.13 dB(A)

Guaranteed sound power level 96 dB(A)

Vibration

max. 2.88 m/s

K=1.5 m/s

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita ELM3800 in the language / languages: English, Dutch as an attachment in your email.

The manual is 2,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita ELM3800

Makita ELM3800 User Manual - English, German, French - 26 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita ELM3800 Manual

Product: