448395
16
Zoom out
Zoom in
Previous page
1/30
Next page
16
- When keeping the machine in storage for a long time, drain fuel from the fuel tank
and carburetor, as follows: Drain all fuel from the fuel tank.
- Remove the spark plug and add a few drops of oil into the spark plug hole. Then,
pull the starter gently to conrm that oil lm covers inside of the engine and
tighten the spark plug.
- Clear dirt or dust from the cutter blade and outside of the engine, wipe them with
a oil-immersed cloth and keep the machine at a place as dry as possible.
STORAGE
After each refuelling Throttle lever
I-O switch
Check the function
Check the function
Before each use Engine assembly,
screws and nuts
Air lter
Cooling air duct
Cutting tool
Idling speed
Fuel tank
Visually check for damage and tightness
Check for general condition and security
Clean
Clean
Check for damage and sharpness
Inspection (cutting tool must not move)
Check and clean
Every 50 hours Gear case Supply grease
Weekly Spark plug Check and replace if necessary
Yearly Fuel pipe Replace
Biyearly Tank cap Replace
Before long term storage Fuel tank
Carburetor
Suction head
Empty and clean
Operate until the engine runs out of fuel
Replace
MAINTENANCE SCHEDULE
FAULT LOCATION
Fault System Observation Cause
Engine not starting or
under difculties
Ignition system Ignition spark is present Faulty fuel supply or compression system, mechanical
defect
No ignition spark I-O switch operated, wiring fault or short circuit, spark
plug or connector defective, ignition module faulty
Fuel supply Fuel tank lled Incorrect choke position, carburetor defective, suction
head (gas line lter) dirty, fuel supply line bent or
interrupted
Compression Inside of engine Cylinder bottom gasket defective, crankshaft seals
damaged, cylinder or piston rings defective
Outside of engine Improper sealing of spark plug
Mechanical fault Starter not engaging Broken starter spring, broken parts inside of the engine
Warm start problems Tank lled Ignition spark
existing
Carburetor contaminated, have it cleaned
Engine starts but dies
immediately
Fuel supply Tank lled Incorrect idling adjustment, suction head or carburetor
contaminated
Fuel tank vent defective, fuel supply line interrupted,
cable or I-O switch faulty
Insufcient performance Several systems may
simultaneously be
affected
Engine idling Air lter contaminated, carburetor contaminated, mufer
clogged, exhaust duct in the cylinder clogged
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita EH7500W at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita EH7500W in the language / languages: English, Dutch as an attachment in your email.

The manual is 4,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita EH7500W

Makita EH7500W User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Spanish - 132 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info