448394
11
Zoom out
Zoom in
Previous page
1/132
Next page
11
Move at least 3 meters away from the place of refuelling. Place the hedge trimmer
on a clean area of ground. Make sure that the cutting blades do not come into
contact with the ground or any other objects.
Cold starting: (When the engine is cold or it has been stopped for more than
5 minutes or when fuel is added to the engine.)
1. Push the I-O switch (1) to “I” position.
2. Repeat pushing the primer pump (2) gently (7 to 10 times) until the fuel comes
into the primer pump.
3. Move the choke lever (3) to position “
”.
4. Hold the hedge trimmer down firmly to avoid loss of control while cranking the
engine. Failure to do so may cause serious injury and/or property damage due to
falling or contact with the cutting blade.
5. Pull the starter handle slowly for 10 to 15 cm until you feel the resistance.
6. Pull the starter handle strongly with feeling the resistance and start the engine.
7. When the engine starts or pop-up and stop, return the choke lever (4) to “
”.
8. Run the engine for approximately one minute at a moderate speed before
accelerating to full throttle.
Note: • If the starter handle is pulled repeatedly when the choke lever
remains at “
” position, the engine will not start easily due to
excessive fuel intake.
In case of excessive fuel intake, remove the spark plug and pull the
starter handle slowly to remove excess fuel. Also, dry the electrode
section of the spark plug.
Hot starting: (Restarting immediately after the engine has stopped.) When
restarting a hot engine, first try the above procedure: 1, 2, 4, 5, 6 with the choke
lever (4) to “
”. If the engine does not start, repeat above steps 1-8.
Note: Do not pull the starter rope to its full extension. Do not allow the
starter grip to be retracted without control. Ensure that it is retracted
slowly.
STARTING THE MACHINE
1. Release the throttle lever completely.
2. Push the I-O switch (1) to “O” position. The engine will slow down and stop.
STOPPING THE MACHINE
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita EH6000W at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita EH6000W in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 6,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita EH6000W

Makita EH6000W User Manual - English, Dutch - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info