448386

Makita EG321AE Manual

22
Zoom out
Zoom in
Previous page
1/49
Next page
14
EN
FR
DE
NL
ES
IT
PT
GR
NO
SE
FI
DK
RU
8. ”HOW-TO” MAINTENANCE
CAUTION
Make sure the engine is stopped before starting
any maintenance, servicing or repair.
NOTE
It is recommended to use ear protection when
performing operation, maintenance and repair of
the generator set.
ENGINE OIL CHANGE (See Fig. 󱌶-①)
■
Change engine oil every 100 hours.
(For new engine, change oil after 20 hours.)
(a) Drain oil by removing the drain plug and the oil fi ller
cap while the engine is warm.
❶ OIL DRAIN PLUG
(b) Reinstall the drain plug and fi ll the engine with oil
until it reaches the upper level on the oil fi ller cap.
■
Use fresh and high quality lubricating oil to
the specifi ed level as directed on page 5. If
contaminated or deteriorated oil is used or the
quantity of the engine oil is not suffi cient, the
engine damage will result and its life will be greatly
shortened.
SERVICING THE AIR CLEANER
(See Fig. 󱌶-② thru ④)
Maintaining an air cleaner in proper condition is very
important.
Dirt induced through improperly installed, improperly
serviced or inadequate elements damages and wears
out engines. Keep the element always clean.
❶ BASE
❷ ELEMENT
❸ AIR CLEANER COVER
❹ BOLT
(a) Remove the bolt of air cleaner cover.
(EG601A, EG601AE, EG671A, EG671AE)
(See Fig.󱌶-④)
Remove the air cleaner cover and cleaner element.
(b) Urethane form : Wash urethane form element in
kerosene or diesel fuel.
Then saturate the element in a mixture of 3 parts
kerosene or diesel fuel and 1 part engine oil.
Squeeze the element to remove the mixture and
install it in the air cleaner.
NOTE
Instead of washing oil (kerosene), it is possible to
wash the urethane foam element in a solution of
mild detergent and warm water.
Then rinse the element thoroughly in clean water.
Allow the element to dry thoroughly.
Soak the element
in clean engine oil and squeeze out excess oil.
CLEANING AND ADJUSTING SPARK PLUG
(See Fig. 󱌶-⑤)
(a) If the plug is contaminated with carbon, remove it
using a plug cleaner or wire brush.
(b) Adjust the electrode gap to 0.6 to 0.7 mm.
Spark plug : BR-6HS (NGK)
CLEANING FUEL STRAINER
(See Fig. 󱌶-⑥)
Dirt and water in the fuel are removed by the fuel
strainer.
(a) Remove the strainer cup and throw away water
and dirt.
(b) Clean the screen and strainer cup with gasoline.
(c) Tightly fasten the cup to main body, making sure to
avoid fuel leak.
CHECKING CARBON BRUSH
Brush Maintenance Essentials
(Effective Length)
The brush is the area which touches the slip ring, and
its surface must be kept smooth.
If it is not smooth then carbon and other substances
will adhere between the brush and slip ring.
This must be buffed with sandpaper or the like
because it is hazardous.
The usable length of the brush is 5~11mm, so if the
brush is 5mm long or less replace it with a new one.
(See Fig.󱌶-⑦)
❶ LENGTH WHEN NEW
❷ EFFECTIVE BRUSH LENGTH
EG671A_en_GU6838.indd 14 2010/01/18 17:14:24
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita EG321AE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita EG321AE in the language / languages: English, Dutch as an attachment in your email.

The manual is 9,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita EG321AE

Makita EG321AE User Manual - German - 49 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info