Manual Makita EG2250A (page 11 of 112) (English, German, Dutch, French, Italian, Spanish)

599869

Zoom out

Zoom in

1/112

Recommended Fuels

This engine is certified to operate on regular unleaded

gasoline with a pump octane rating of 86 or higher.

Never use stale or contaminated gasoline or an oil-

gasoline mixture. Avoid getting dirt or water in the fuel

tank.

Regular unleaded gasoline containing no more than 10%

ethanol (E10) or 5% methanol by volume can be used. In

addition, the methanol must contain cosolvents and

corrosion inhibitors.

If fuels containing levels of ethanol or methanol greater

than those shown above are used, starting and/or

performance problems may occur. The metal, rubber, and

plastic parts of the fuel system may also be damaged.

Engine damage or performance problems resulting from

the use of fuel with percentages of ethanol or methanol

greater than the values shown above are not covered by

the warranty.

STARTING/STOPPING THE

ENGINE

Starting the Engine

For safety reasons, do not operate the generator in an

enclosed area such as a garage. The generator’s exhaust

contains poisonous carbon monoxide gas that can collect

rapidly in an enclosed area and cause illness or death.

WARNING:

Exhaust from the generator contains poisonous

carbon monoxide gas that can build up to dangerous

levels in closed areas.

Inhaling carbon monoxide can cause

unconsciousness or death.

Never run the generator in a closed or partially closed

area where people may be present.

To prevent fires, keep the generator at least 3 feet

(1 meter) away from buildings and other structures during

operation. Keep flammable objects away from the engine.

NOTICE:

Do not operate this generator less than 3 feet (1 meter)

from a building or other obstruction. Doing so can cause

overheating and/or damage the generator. In order to

maintain proper cooling, allow at least 3 feet (1 meter) of

empty space above and around the generator.

Refer to the “AC OPERATION” or “DC OPERATION” of

this manual for how to connect loads to the generator.

1. Perform the PRE-OPERATION CHECKS.

2. Make sure that the AC circuit breaker is in the

“O (OFF)” position. It may be difficult to start the

generator if a load is connected.

3. Turn the fuel valve lever to the “I (ON)” position.

4. Turn the engine switch to the “I (ON)” position.

5. Pull the starter grip slowly until resistance is felt, then

pull swiftly.

NOTICE:

Return the starter grip back gently to prevent damage to

the starter. Do not let it snap back against the engine.

With the electric starter:

1. Connect the battery cables to the generator.

2. Turn the engine switch to the “S (START)” position

and hold it there for 5 seconds or until the engine

starts.

NOTICE:

• The motor can be damaged if the starter motor is

operated for more than 5 seconds. If the engine fails to

start, release the switch and wait 10 seconds before

operating the starter again.

• If the speed of the starter motor drops after a period of

time, it is an indication that the battery should be

recharged.

When the engine starts, allow the engine switch to return

to the “I (ON)” position.

If the choke was manually closed, push it to the “OPEN”

position as the engine warms up.

Stopping the Engine

In an emergency:

To stop the engine in an emergency, move the engine

switch to the “O (OFF)” position.

In normal use:

1. Turn the AC circuit breaker to the “O (OFF)” position.

Disconnect the DC battery charging cables.

2. Turn the engine switch to the “O (OFF)” position.

3. Turn the fuel valve lever to the “O (OFF)” position.

MAINTENANCE

The Importance of Maintenance

Good maintenance is vital to the safe, economical, and

trouble free operation of the generator. It will also help

reduce air pollution.

WARNING:

Improper maintenance, or failure to correct a problem

before operation, can cause a malfunction which can

result in severe personal injury or loss of life.

Always follow the inspection and maintenance

recommendations and schedules in this instruction

manual.

The following pages include a maintenance schedule,

routine inspection procedures, and simple maintenance

procedures using basic hand tools required for properly

caring for the generator. Other service tasks that are more

complicated or require special tools are best handled by

professionals and are normally performed by a Makita

technician or other qualified mechanic.

The maintenance schedule included in this manual is

based on normal operating conditions. If the generator is

operated under severe conditions, such as sustained

high-load or high-temperature operation, or it is used in

unusually wet or dusty conditions, consult your servicing

dealer for recommendations applicable to your specific

needs and use.

Maintenance, replacement, or repair of the emission

control devices and systems may be performed by

any nonroad engine repair establishment or

individual, using parts that are ‘‘certified’’ to EPA

standards.

Maintenance Safety

The following are some of the most important safety

precautions. However, we cannot cover every

conceivable hazard that can arise in performing

maintenance, so please remember that only you can

decide whether or not you should perform a given task.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita EG2250A in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,06 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita EG2250A Manual

Product: