599867

Makita EBH341U Manual

10
Zoom out
Zoom in
Previous page
1/232
Next page
10
To meet the applicable safety provisions, only the tool/protector
combinations as indicated in the table must be used.
Be sure to use genuine MAKITA cutter blades or
nylon cutting head.
– The cutter blade must be well polished, free of cracks or
breakage. If the cutter blade hits against a stone during
operation, stop the engine and check the blade immediately.
– Resharpening or replace the cutter blade every three hours of
operation.
– If the nylon cutting head hits against a stone during operation,
stop the engine and check the nylon cutting head immediately.
CAUTION: The appropriate protector must always be installed, for
your own safety and in order to comply with accident-
prevention regulations.
Operation of the equipment without the guard being in
place is not permitted.
The outside diameter of the cutter blade must be
255 mm (10”). Cutter blades with outside diameter of
305 mm or 12 inches can be used only for those with
three blades.
Metal blade
Protector for metal blades
Nylon cutting head
Protector for
nylon cutting head
MOUNTING OF PROTECTOR
– In use of the metal blade, fix the protector (3) to the clamp (2) with two bolts
M6 x 30 (1).
NOTE: Tighten the right and left bolts evenly so that the gap between the clamp
(2) and the protector (3) will be constant.
Otherwise, the protector sometimes may not function as specified.
– In cases where the nylon cord cutter is to be used, be sure to mount the
nylon cord cutter protector (4) onto the metal blade protector (3).
– Mount the nylon cord cutter protector (4) by sliding it into place from the flank
of the metal blade protector (3) as shown.
– Remove tape adhered to cutter, which cuts nylon cord, on nylon cord cutter
protector (4).
CAUTION: Be sure to push in nylon cord cutter protector (4) until it is fully
inserted.
Take care not to injure yourself on the cutter for cutting the nylon
cord.
(3)
(2)
(1)
(3)
(4)
– To remove the nylon cord cutter protector (4), apply a hex wrench into the
notch on the metal blade protector (3), push it in and meanwhile slide the
nylon cord cutter protector (4).
Hex wrench
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita EBH341U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita EBH341U in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 5,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info