690563
14
Zoom out
Zoom in
Previous page
1/172
Next page
3. The appropriate clearance between two electrodes of spark plug
is 0.7 to 0.8 mm. Adjust to the correct clearance when it is too wide or
too narrow.
Clean thoroughly or replace the spark plug if it has accumulated car-
bon or contaminated.
For replacement, use NGK CMR6H.
0.7 mm – 0.8 mm (0.028″ – 0.031″)
4. To close the plug cover, make a half turn of it, and press around
the dented part.
1
1. Plug cover
Cleaning the fuel lter
CAUTION: Make sure there is no damage on the fuel tank.
If there are any damage on the fuel tank, ask authorized service
center immediately for repair.
NOTICE: Clean the fuel lter regularly. Clogged fuel lter may
cause difculty of start-up or failure of engine speed increase.
Check the fuel lter regularly as follows:
1
2
3
1. Fuel tank cap 2. Fuel lter 3. Hose clamp
1. Remove the fuel tank cap, drain the fuel to empty the tank.
Check the tank inside for any foreign materials. If any, wipe clean
such materials.
2. Pull out the fuel lter with wire through the fuel lling port.
3. If the fuel lter surface is contaminated, clean it with gasoline.
NOTICE: Follow the method specied by each local authority
for disposing the gasoline used for cleaning the fuel lter.
NOTICE: Replace the fuel lter if it is excessively
contaminated.
4. After checking, cleaning or replacing, insert the fuel lter into the
fuel pipe and x it with the hose clamp. Reset the fuel lter in the fuel
tank and tighten rmly the fuel tank cap.
Adjustment of idling speed
CAUTION: The carburetor is factory adjusted. Never adjust
other than idling speed. For other adjustments, ask your autho-
rized service center.
Appropriate low-speed rotation is 2,800 min
-1
(rpm).
If it is necessary to change the rotation speed, adjust the idle speed
with a Phillips screwdriver.
If the engine stops or runs unsteadily at idle, turn the adjusting screw
to the right, and the idling speed increases. If the machine blows too
strong at idle, turn the adjusting screw to the left, and the idling speed
drops.
1
1. Idling adjusting screw
14 ENGLISH
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita EB7660TH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita EB7660TH in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 42,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info