690911
18
Zoom out
Zoom in
Previous page
1/54
Next page
18
Refuelling and relling chain oil
WARNING:
FOLLOW THE SAFETY PRECAUTIONS. Be careful and cautious when handling
fuels.
Switch off the engine.
CAUTION:
Clean the tank cap and the area around the tank after refuelling.
Refuel or rell the chain oil as follows:
1. Thoroughly clean the area around the caps, to prevent dirt from getting into the
fuel or oil tank.
2. Unscrew the cap and ll the each tanks with fuel (fuel/oil mixture) and chain oil
respectively.
3. Fill up to the bottom edge of the ller neck. Be careful not to spill fuel or chain oil!
4. Tighten the tank caps by hand as far as it goes.
Lubricating the chain
WARNING:
Check the chain oil tank only when the engine is switched off.
Make sure there is sufcient chain oil in the chain oil tank to provide good chain
lubrication during operation.
At medium oil feed rate, the oil tank capacity is approximately equal to the run time
of one tank of fuel.
Before operation or refueling, check the chain oil level and rell if necessary.
Adjusting the chain lubrication
WARNING:
Switch off the engine.
You can adjust the oil pump feed rate with adjusting screw. There are three degrees
of the oil pump feed rate, i.e. high, middle or low.
Adjusting screw locates at the bottom of the chain saw. Use a screwdriver and
adjust the amount of oil delivery appropriately.
Cleaning the oil guide
To ensure secure operation of the oil pump, clean the oil guide groove at the
housing and the oil feed hole in the guide bar regularly.
Checking the chain lubrication
CAUTION:
Never work with the chain saw without sufcient chain lubrication. Otherwise the
service life of the saw chain and guide bar is reduced.
Before starting work check the oil level in the tank and the oil feed.
Pay attention to the direction of the wind and avoid unnecessary exposure to the
oil spray.
Check the oil feed rate as follows:
1. Start the chain saw.
2. Hold the running chain saw approx. 15 cm (6”) above a trunk or the ground (use
an appropriate base).
3. If the lubrication is sufcient, you can see light oil trace because oil is scattered
off the chain.
NOTE:
After turning off the chain saw, it is normal that residual chain oil drips from the
oil feed system, the guide bar and the chain for a while. This does not mean a
defect. Place the saw on a suitable surface.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita EA3601F at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita EA3601F in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 12,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info