Manual Makita dw 6015 (page 5 of 23) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

386596

Zoom out

Zoom in

1/23

Switch action (Fig. 4)

Move the reversing switch lever to the position

for clockwise rotation or the

position for counter-

clockwise. To start the tool, simply pull the trigger.

Release the trigger to stop. When the reversing

switch lever is in the neutral positioin, the tool will not

start even if you pull the trigger.

CAUTION:

•

Before inserting the battery cartridge into the

machine, always check to see that the switch trigger

actuates properly and returns to the ‘‘OFF’’ position

when released.

•

Always check the direction of rotation before drilling.

•

Use the reversing switch lever only when the

machine comes to a complete stop. Changing the

direction of rotation before the tool stops may ruin

the tool.

•

When not operating the tool, keep the reversing

switch lever in the neutral position.

Speed change (Fig. 5)

To change the machine speed, turn the speed change

knob so that the arrow of the desired speed on the

knob is aligned with the reference arrow on the

machine body. If the speed change knob does not

turn easily, switch on the machine and turn the knob

again while the machine is running under no load.

Drilling operation

•

Drilling in wood

When drilling in wood, best results are obtained with

wood drills equipped with a guide screw. The guide

screw makes drilling easier by pulling the bit into the

workpiece.

•

Drilling in metal

To prevent the bit from slipping when starting a hole,

make an indentation with a center-punch and ham-

mer at the point to be drilled. Place the point of the

bit in the indentation and start drilling.

Use a cutting lubricant when drilling metals. The

exceptions are iron and brass which should be

drilled dry.

CAUTION:

•

Pressing excessively on the machine will not speed

up the drilling. In fact, this excessive pressure will

only serve to damage the tip of your bit, decrease

the machine performance and shorten the service

life of the machine.

•

There is a tremendous force exerted on the

machine/bit at the time of hole breakthrough. Hold

the machine firmly and exert care when the bit

begins to break through the workpiece.

•

A stuck bit can be removed simply by setting the

reversing switch to reverse rotation in order to back

out. However, the machine may back out abruptly if

you do not hold it firmly.

•

Always secure small workpieces in a vise or similar

hold-down device.

Screwdriving operation (Fig. 6)

Place the point of the driver bit in the screw head and

apply pressure to the machine. Start the machine

slowly and then increase the speed gradually.

Release the trigger as soon as the clutch cuts in.

NOTE:

•

Make sure that the driver bit is inserted straight in

the screw head, or the screw and/or bit may be

damaged.

•

When driving wood screws, predrill pilot holes to

make driving easier and to prevent splitting of the

workpiece. See the chart.

Nominal diameter of

wood screw (mm)

Recommended size of

pilot hole (mm)

3.1 2.0 – 2.2

3.5 2.2 – 2.5

3.8 2.5 – 2.8

4.5 2.9 – 3.2

4.8 3.1 – 3.4

5.1 3.3 – 3.6

Overload protector

The overload protector automatically cuts out to break

the circuit and the button pops out, whenever heavy

work is prolonged. Wait 20 – 30 seconds before

pressing the restart button to resume operation. Your

finger should not be on the trigger when you press the

restart button, however.

MAINTENANCE

CAUTION:

Always be sure that the machine is switched off and

the battery cartridge is removed before carrying out

any work on the machine.

To maintain product safety and reliability, repairs,

maintenance or adjustment should be carried out by a

Makita Authorized Service Center.

6015DWE (E) (’100. 3. 15)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita dw 6015 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita dw 6015 Manual

Product: