691397

Makita DVP180 Manual

7
Zoom out
Zoom in
Previous page
1/60
Next page
7 ENGLISH
► Fig.2:
1. Red indicator
2. Button
3. Battery cartridge
To remove the battery cartridge, slide it from the pump
while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place with
a little click. If you can see the red indicator on the upper
side of the button, it is not locked completely.
CAUTION: Always install the battery cartridge
fully until the red indicator cannot be seen. If not, it
may accidentally fall out of the pump, causing injury to
you or someone around you.
CAUTION: Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is not
being inserted correctly.
Battery protection system
► Fig.3:
1. Star marking
The pump is equipped with a battery protection system.
This system automatically cuts off power to the motor to
extend battery life.
The pump will automatically stop during operation if the
pump and/or battery are placed under one of the following
conditions:
Overloaded:
The pump is operated in a manner that causes it to draw
an abnormally high current.
In this situation, turn the pump off and stop the application
that caused the pump to become overloaded. Then turn
the pump on to restart.
If the pump does not start, the battery is overheated.
In this situation, let the battery cool before turning the
pump on again.
Low battery voltage:
The remaining battery capacity is too low and the pump
will not operate. In this situation, remove and recharge
the battery.
NOTE: The overheat protection works only with a
battery cartridge with a star marking.
Indicating the remaining battery
capacity
Only for battery cartridges with “B” at the end of the
model number
► Fig.4:
1. Indicator lamps 2. Check button
Press the check button on the battery cartridge to indicate
the remaining battery capacity. The indicator lamps light
up for few seconds.
Indicator lamps Remaining
capacity
Lighted Off
Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
The battery
may have
malfunctioned.
NOTE: Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
OPERATION
The pump does not contain oil when newly purchased.
Refer to “Adding oil” and add oil.
WARNING: Operating the pump in the
condition without oil added will damage the pump.
In addition, the oil tank will become hot and may result
in burns or other accidents.
Adding oil
► Fig.5:
1. Oil ll/Exhaust cap
2. Level line
3. Sight glass
4. Oil tank
1. Remove the oil ll/exhaust cap and add the supplied
oil via the ller port.
NOTICE: Always use Makita genuine oil in order to
maintain pump performance.
2. Add oil until the oil level is between the upper and
lower level lines of the sight glass.
NOTICE: The oil level is important. Operating the
pump in the condition with the oil level not between the
upper and lower level lines may result in malfunction.
Checking performance
► Fig.6:
1. Intake
2. Low side valve
3. Vacuum pump
4. Manifold
1. Connect the low side valve of the manifold and the
intake port of the pump with a charging hose.
2. Close the low side valve of the manifold.
3. Open the intake shut-off valve.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DVP180 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DVP180 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 6,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info