Manual Makita DVC864L (page 11 of 128) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691507

Zoom out

Zoom in

1/128

11 ENGLISH

Indicator lamps Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may differ slightly

from the actual capacity.

Indicating the remaining battery

capacity

► Fig.4: 1. Battery indicator 2. Check button

3. Stand-by switch

► Fig.5

Press the check button to indicate the remaining battery

capacities. The battery indicators correspond to each

battery.

Battery indicator status Remaining

battery

capacity

Off

Blinking

50% to 100%

20% to 50%

0% to 20%

Charge the

battery

NOTE: During the cleaner turned on with the stand-by

switch set to "AUTO", the battery indicator does not

work.

Tool / battery protection system

The tool is equipped with a tool/battery protection sys-

tem. This system automatically cuts off power to the

motor to extend tool and battery life. The tool will auto-

matically stop during operation if the tool or battery is

placed under one of the following conditions:

Overload protection

When the tool is operated in a manner that causes it to

draw an abnormally high current, the tool automatically

stops without any indication. In this situation, turn the

tool off and stop the application that caused the tool to

become overloaded. Then turn the tool on to restart.

Overheat protection

On Blinking

When the tool is overheated, the tool stops automatically, and

the battery indicator blinks about 60 seconds. In this situa-

tion, let the tool cool down before turning the tool on again.

Overdischarge protection

When the battery capacity becomes low, the tool stops

automatically. If the product does not operate even

when the switches are operated, remove the batteries

from the tool and charge the batteries.

Switch action

► Fig.6: 1. Stand-by switch 2. Power button 3. Suction

force adjusting knob

To start the cleaner:

1. Set the stand-by switch to the "I" side. The cleaner

gets into stand-by state.

2. Press the power button.

To make the cleaner get into stand-by mode, press the

power button again.

To turn off the cleaner, set the stand-by switch to the "O" side.

The suction power can be adjusted according to your work need.

Suction power can be increased by turning the suc-

tion force adjusting knob from the symbol to

the symbol.

NOTICE: Always set the stand-by switch to the "O"

side when not using the cleaner for long time. The

cleaner consumes power during stand-by state.

Locking or unlocking the caster

► Fig.7: 1. Caster 2. Stopper lever 3. FREE position

4. LOCK position

Locking the caster is convenient when storing the cleaner,

stopping the work on the way and keeping the cleaner still.

To operate the stopper, move it by hand.

To lock the caster with a stopper, lower the stopper

lever and the caster no longer will rotate. To release the

caster from the locked position, raise the stopper lever.

NOTE:

When moving the cleaner, make sure that the

caster is unlocked. Moving the cleaner with the caster

in the locked position may cause damage to the caster.

Carriage handle

When carrying the cleaner, carry it by holding the han-

dle on the head. The handle is retractable at the head

when not in use.

► Fig.8

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DVC864L in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 19,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DVC864L Manual

Product: