Manual Makita DVC261 (page 13 of 25) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691488

Zoom out

Zoom in

1/25

13 ENGLISH

Connecting the tool

NOTE: If the bent pipe assembly is attached to the

hose, remove it beforehand.

To connect a tool to the cleaner, the dedicated hose and/or addi-

tional parts are required. Depending on your cleaner model, you

need to replace the hose and/or prepare additional parts.

Refer to the following table for details.

Supplied

hose

diameter

Hose end type Action

ø28 mm

without part

Attach the front cuff.

with snap-on part

Replace the hose end

(snap-on part) with the front

cuff.

The hose end can be removed

by turning it counterclockwise.

ø32 mm

with snap-on part

Replace the hose with the one

for dust extraction (ø28 mm,

with front cuff).

ø38 mm

with snap-on part

Replace the hose with the one

for dust extraction (ø28 mm,

with front cuff).

with front cuff 38

Attachthejoint22-38orthe

front cuff 24.

NOTE:

Always use a suitable front cuff. When using the front

cuff 24, attach it to the front cuff 22 that is connected to the hose.

►Fig.20: 1. Front cuff 22 2. Front cuff 24

When using ø28 mm dust extraction hose

1. Attach the front cuff to the hose for dust extraction.

When connecting the front cuff, make sure that it is

securely screwed on the hose.

Connect the front cuff to the tool's extraction outlet.

►Fig.21: 1. Front cuff 2. Extraction outlet 3. Hose

The front cuff can be detached by turning it counter-

clockwise while holding the hose.

When using ø38 mm hose with front cuff 38

1. Twistandinsertthejointorthefrontcufftothe

inlet part on the hose, depending on the tool that you

are going to connect.

Connect the front cuff to the tool's extraction outlet.

►Fig.22: 1. Joint 2. Front cuff 3. Extraction outlet

4. Hose

Toremovethejointandthefrontcuff,followtheinstalla-

tion procedures in reverse.

Attaching bent pipe assembly

Optional accessory

NOTE: You don't need to perform this procedure

if your model comes with the bent pipe assembly

attached to the hose.

NOTE: There are two types of bent pipe assembly;

the one for slide-type extension wand and the one for

ring-type extension wand. If you prepare the bent pipe

assembly, choose the one for your desired extension

wand type.

The bent pipe assembly is used for connecting the exten-

sion wand or nozzle for vacuum cleaning to this product.

If you want to use this product as the vacuum cleaner,

attach the bent pipe assembly to the hose.

To attach, unscrew the front cuff from the hose and

fasten the sleeve of bent pipe assembly onto the hose.

To remove, loosen the sleeve of bent pipe assembly

from the hose.

►Fig.23: 1. Hose 2. Bent pipe assembly 3. Sleeve

Installing lter bag / dust bag

Optional accessory

CAUTION:

Do not use a damaged lter bag.

Always use the vacuum cleaner with the lter bag

properly installed. Otherwise the vacuumed dust or

particles may be exhausted from the cleaner and

they may cause respiratory disease to the operator.

NOTICE:Whenthelterbagisalreadyfull,replace

with new one. When the dust bag is already full,

emptyit.Continuoususewiththelterbag/dustbag

full results in reduced suction power.

1. Unlock the latch by lifting the bottom side. Push

the grooved area to lift the front latching side. Pull the

latch to open the lid.

►Fig.24: 1. Hook 2. Lid

2. Insertthelterbagintotheslitontheuppersideof

the room as illustrated.

►Fig.25: 1. Slit 2. Filter bag

When using the dust bag, insert the brim of the dust bag

into the slit.

►Fig.26: 1. Slit 2. Brim 3. Dust bag

Aligntheholeofthelterbagwiththehosecuffand

push the cardboard portion to the end. Make sure that the

rubberringonthelterbaggoesovertherimonthehosecuff.

►Fig.27: 1.Rubberringonthelterbag2. Rim on

the hose cuff 3. Cardboard portion of the

lterbag4. Hose cuff

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DVC261 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 5,12 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DVC261 Manual

Product: