691284

Makita DUT130 Manual

9
Zoom out
Zoom in
Previous page
1/64
Next page
9 ENGLISH
Electronic function
Thetoolisequippedwiththeelectronicfunctionsfor
easyoperation.
• Soft start
The soft-start function minimizes start-up shock,
andmakesthetoolstartsmoothly.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing the front cover and side
grip
CAUTION: Tighten the side grip rmly.
Otherwise,thefrontcovermayfallandcausean
injury.
►Fig.7: 1. Front cover 2. Side grip
Attach the front cover to the tool and screw the side grip
onthetoolsecurely.
The side grip can be installed on either side of the tool.
Installing the shaft
Optional accessory
For DUT130
1. Tighten the shaft into the shaft holder.
►Fig.8: 1. Shaft 2. Shaft holder
2. Tighten the shaft with wrench while holding the
shaft holder with another wrench.
►Fig.9: 1. Shaft 2. Shaft holder
For DUT131
1. Insert the shaft into the chuck as far as it will go.
►Fig.10: 1. Shaft 2. Chuck
2. Tightenthechuckbyhand,andthenplacethe
chuckkeyineachofthreeholesandtightenitclock-
wise.Besuretotightenthechuckkeyatallthreeholes
evenly.
►Fig.11: 1.Chuckkey2. Chuck
Toremovetheshaft,turnthechuckkeycounterclock-
wiseatoneoftheholes,andthenloosenthechuckby
hand.
Installing the mixing blade
Optional accessory
Attach the mixing blade on the top of the shaft, and then
secure it with the hex bolt.
►Fig.12: 1. Mixing blade 2. Shaft 3. Hex bolt
NOTICE: Be sure to attach the mixing blade with
"UP" mark facing the tool.
►Fig.13: 1. Mark
Hook
Optional accessory
CAUTION: Always remove the battery when
hanging the tool with the hook.
CAUTION: Never hook the tool at high loca-
tion or on potentially unstable surface.
►Fig.14: 1. Groove 2. Hook 3. Screw
Thehookisconvenientfortemporarilyhangingthetool.
This can be installed on either side of the tool.
To install the hook, insert it into a groove in the tool
housing on either side and then secure it with a screw.
To remove, loosen the screw and then take it out.
Installing or removing the shaft
holder
Optional accessory
For DUT131
1. Insert the hex wrench into the chuck, and then
loosen the chuck with the hex wrench while holding the
spindle with the wrench.
►Fig.15: 1. Hex wrench 2. Chuck 3. Wrench
2. Tighten the shaft holder with a wrench while hold-
ing the spindle with another wrench.
►Fig.16: 1. Shaft holder 2. Wrench
To remove the shaft holder, perform the installation
procedure in reverse.
OPERATION
CAUTION: Do not mix ammable materials or
operate the tool around ammable materials such
as paint with thinner used as solvent. Failure to do
somaycauseaninjury.
CAUTION: Do not mix high viscosity material,
such as mortar or adhesive, in the high speed
mode.Youmaylosethecontrolofthetoolandcause
aninjury.
NOTICE: When you mix the material while the
mixing blade oating out of the material, be care-
ful not to splash the material.
1. Select high speed or low speed according to the
material to be mixed.
2. Hold the rear handle of the tool with one hand
andthegripwiththeotherhandrmly,placethemixing
bladeundermaterialfullyandturnonthetoolafter
makingsureworksitesafety.
3. Move the mixing blade up and down during the
mixing operation so that whole part of material can be
mixed.
4. Whennishingmixing,turnoffthetool,makesure
that the mixing blade has come to a complete stop, and
then pull it out of the mixing container.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DUT130 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DUT130 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 12,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info