Manual Makita DUR362L (page 17 of 128) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

599968

Zoom out

Zoom in

1/128

Installing the cutter blade (country

specific)

WARNING:

• The outside diameter of the cutter blade must be

230 mm. Never use any blade exceeding 230 mm in

outside diameter.

CAUTION:

• The cutter blade must be well polished, free of cracks

or breakage. Polish or replace the cutter blade every

three hours of operation.

• Always wear gloves when handling the cutter blade.

• Always attach the blade cover when the tool is not in

use or is being transported.

• The cutter blade-fastening nut (with spring washer)

wears out in course of time. If there appears any wear

or deformation on the spring washer, replace the nut.

Ask your local authorized service center to order it.

NOTICE:

• Be sure to use genuine Makita cutter blade.

Turn the tool upside down so that you can replace the

cutter blade easily.

To dismount the cutter blade, insert the hex wrench

through the hole on the protector cover and the gear case.

Rotate the receive washer until it is locked with the hex

wrench. Loosen the hex nut (left-hand thread) with the

socket wrench and remove the nut, clamp washer and

hex wrench. (Fig. 29)

Mount the cutter blade onto the shaft so that the guide of

the receive washer fits in the arbor hole in the cutter

blade. Install the clamp washer and secure the cutter

blade with the hex nut with 13 to 23 Nm of tightening

torque during holding the receive washer with hex

wrench. (Fig. 30)

Make sure that the blade is the left way up. (Fig. 31)

Hex wrench storage (Fig. 32)

When not in use, store the hex wrench as shown in the

figure to keep it from being lost.

OPERATION

Correct handling of tool (DUR361U)

Correct posture

WARNING:

• Always position the tool on your right-hand side so

that the shaft of the left handle is always in front of

your body. Correct positioning of the tool allows for

maximum control and will reduce the risk of serious

personal injury caused by kickback.

As shown in the figure fit the shoulder harness and hang

the tool firmly on your right side so that the shaft of the left

handle is always ahead of you. (Fig. 33)

Attachment of shoulder harness (Fig. 34)

Wear the shoulder harness on your back and buckle it up

until a click is heard. Make sure that it cannot be taken off

with pulling it off. Hang the tool as shown.

WARNING:

• Be extremely careful to maintain control of the tool

at this time. Do not allow the tool to be deflected

toward you or anyone in the work vicinity. Failure to

do so could result in serious injury.

Adjustment of the hanger position and shoulder

harness

When replacing battery or accessories with others, the

weight balance of the tool may change. In such case,

adjust the hanger position and shoulder harness length as

follows.

To change the hanger position, loosen the fixing screw on

the hanger with the supplied wrench and then move the

hanger and the cushion. The cushion can be moved

easily by twisting it.

Adjust the hanger position and shoulder harness length

so that: (Fig. 35)

– the hanger positions 750 mm or higher from the

ground,

– the cutting tool positions 100 mm to 300 mm high from

the ground and

– the unguarded part of cutting tool is horizontally

750 mm or farther away from the hanger.

After adjusting the hanger position, tighten the screw with

the wrench securely.

Correct handling of tool (DUR362L)

Correct posture

WARNING:

• Always position the tool on your right-hand side so

that the barrier is always in front of your body.

Correct positioning of the tool allows for maximum

control and will reduce the risk of serious personal

injury caused by kickback.

As shown in the figure, put the shoulder harness on your

left shoulder by putting your head and right arm through it

and keep the tool on your right side while always keeping

the barrier in front of your body. (Fig. 36)

Attachment of shoulder harness (Fig. 37)

After putting the shoulder harness on it can be attached to

the tool by connecting the buckles provided on both the

tool hook and the harness. Be sure that the buckles click

and lock completely in place.

Detachment (Fig. 38)

The buckle is provided with a means of quick release

which can be accomplished by simply squeezing the

sides and the buckle.

WARNING:

• Be extremely careful to maintain control of the tool

at all times. Do not allow the tool to be deflected

toward you or anyone in the work vicinity. Failure to

keep control of the tool could result in serious injury to

the bystander and the operator.

MAINTENANCE

WARNING:

• Always be sure that the tool is switched off and

battery cartridge is removed before attempting to

perform inspection or maintenance on the tool.

Failure to switch off and remove the battery cartridge

may result in serious personal injury from accidental

start-up.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DUR362L in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 22,68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DUR362L Manual

Product: