690923

Makita DUR189 Manual

14
Zoom out
Zoom in
Previous page
1/116
Next page
14 ENGLISH
ASSEMBLY
WARNING: Always be sure that the tool is
switched off and battery cartridge is removed
before carrying out any work on the tool. Failure to
switch off and remove the battery cartridge may result
inseriouspersonalinjuryfromaccidentalstart-up.
WARNING: Never start the tool unless it is
completely assembled. Operation of the tool in a
partially assembled state may result in serious per-
sonalinjuryfromaccidentalstart-up.
Installing the handle
Fit the handle onto the shaft and secure it with the bolt
and the knob.
►Fig.13: 1. Handle 2. Bolt 3. Knob 4. Cutting tool
side 5. Battery cartridge side
Make sure that the handle is located in the straight area
oftheshaftasshowninthegure.
►Fig.14
Installing the protector
WARNING: Never use the tool without the
protector illustrated in place. Failure to do so can
causeseriouspersonalinjury.
CAUTION: Take care not to injure yourself on
the cutter for cutting the nylon cord.
NOTE: The shape of the protector varies depending
on the country.
1. Attach the protector and the protector holder to the
motorhousingasillustrated.Besuretottheprojec-
tions and grooves on them to their counter parts.
►Fig.15: 1. Protector 2. Groove 3.Projection
4. Protector holder
2. Tighten the hex socket head bolts securely to
fasten the protector and the protector holder.
►Fig.16: 1. Hex socket head bolt 2. Hex wrench
Installing the wire guard
CAUTION: Before adjusting the wire guard,
wait for the cutting head comes to standstill. Do
not adjust the wire guard with your foot.
►Fig.17
Toreducetheriskdamagingtheobjectsinfrontofthe
cutting head, insert the wire guard so that it controls the
cutting range of the mowing line.
Slightly expand the wire guard outward and then insert
it into the holes on the protector.
►Fig.18: 1. Wire guard 2. Hole (on both sides)
NOTICE: Do not expand the wire guard outward too
much. Otherwise it may break.
When wire guard is not in use, lift it for the idle position.
►Fig.19
Installing nylon cutting head
Optional accessory
CAUTION: If the nylon cutting head acciden-
tally impacts a rock or hard object during oper-
ation, stop the tool and inspect for any damage.
If the nylon cutting head is damaged, replace it
immediately. Use of a damaged cutting tool could
resultinseriouspersonalinjury.
CAUTION: Be sure to remove the hex wrench
after installation.
NOTICE: Be sure to use genuine Makita nylon
cutting head.
►Fig.20: 1. Nylon cutting head 2. Metal guard
3. Spindle 4. Hex wrench 5. Tighten
6. Loosen
1. Turn the tool upside down so that you can replace
the cutting tool easily.
2. Insert the hex wrench through the hole on the
motor housing and rotate the spindle until the spindle is
locked.
3. Place the nylon cutting head onto the threaded
spindle directly and tighten it by turning in the tightening
directionasshowninthegure.
4. Remove the hex wrench.
To remove the nylon cutting head, turn it in the opposite
direction while locking the spindle with the hex wrench.
Installing plastic blade
Optional accessory
CAUTION: If the plastic blade accidentally
impacts a rock or hard object during operation,
stop the tool and inspect for any damage. If the
plastic blade is damaged, replace it immediately.
Use of a damaged cutting tool could result in serious
personalinjury.
CAUTION: Be sure to remove the hex wrench
after installation.
NOTICE: Be sure to use genuine Makita plastic
blade.
►Fig.21: 1. Plastic blade 2. Metal guard 3. Hex
wrench 4. Tighten 5. Loosen
1. Turn the tool upside down so that you can replace
the cutting tool easily.
2. Insert the hex wrench through the hole on the
motor housing and rotate the spindle until the spindle is
locked.
3. Place the plastic blade onto the threaded spindle
directly and tighten it by turning in the tightening direc-
tionasshowninthegure.
4. Remove the hex wrench.
To remove the plastic blade, turn it in the opposite direc-
tion while locking the spindle with the hex wrench.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DUR189 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DUR189 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 23,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info