Manual Makita DUH523 (page 10 of 68) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

599985

Zoom out

Zoom in

1/68

Removing or installing shear blade

CAUTION:

• Before removing or installing shear blade, always be

sure that the tool is switched off and the battery

cartridge is removed.

• When replacing the shear blade, always wear gloves

without removing blade cover so that hands and face

does not directly contact the blade. Failure to do so

may cause personal injury.

NOTE:

• Do not wipe off grease from the gear and crank. Failure

to do so may cause damage to the tool.

Removing the shear blades (Fig. 16)

Reverse the tool and loosen four screws and remove the

under cover.

NOTE:

• Be careful not to get your hands dirty as grease is

applied in the shear blade driving area. (Fig. 17)

Loosen four screws and remove the blades. Remove the

washer and sponge from the shear blades and put them

aside. They are required for the later installation. (Fig. 18)

If the sleeves are still left in the holes of the gear, remove

the gear and push the sleeves out of it with a screwdriver

or the like.

NOTE:

The washer underneath the gear may come off by

mistake when removing the gear. In this case, return it to

the original position as it was installed.

Installing the shear blade (Fig. 19)

Remove the blade cover from the old shear blades and fit

it onto the new ones to avoid contact with blades.

(Fig. 20)

Adjust the hole positions by turning the gear as illustrated.

(Fig. 21 & 22)

Apply some grease provided with the new shear blades

as illustrated. (Fig. 23)

Put the removed sponge in the same position as the old

one. Make sure that the sleeves provided with the new

shear blades are put on the pins of the blade. Place the

new shear blades on the tool so that the pins fit in the

holes of the gear. If the sleeves on the pins come off

mistakenly, put them into the holes of the gear

beforehand. (Fig. 24)

Install the blade and tighten the four screws and put the

removed washer in the same position as the old one.

(Fig. 25)

Install the under cover on the tool and tighten the four

screws firmly.

Storage

The hook hole in the tool bottom is convenient for hanging

the tool from a nail or screw on the wall. (Fig. 26)

Remove the battery cartridge and put the blade cover on

the shear blades so that the blades are not exposed.

Store the tool out of the reach of children carefully.

Store the tool in the place not exposed to water and rain.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Blade cover

• Shear blade assembly

• Makita genuine battery and charger

• Chip receiver

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ

from country to country.

Noise

ENG905-1

The typical A-weighted noise level determined according

to EN60745:

Model DUH481, DUH483, DUH521

Sound pressure level (L

): 75 dB (A)

Uncertainty (K): 2.5 dB (A)

The noise level under working may exceed 80 dB (A).

Model DUH523

Sound pressure level (L

): 77 dB (A)

Uncertainty (K): 2.5 dB (A)

The noise level under working may exceed 80 dB (A).

Wear ear protection.

Vibration

ENG900-1

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Work mode: hedge trimming

Vibration emission (a

): 2.5 m/s

or less

Uncertainty (K): 1.5 m/s

ENG901-1

• The declared vibration emission value has been

measured in accordance with the standard test method

and may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of exposure in

the actual conditions of use (taking account of all parts

of the operating cycle such as the times when the tool

is switched off and when it is running idle in addition to

the trigger time).

For European countries only

ENH040-4

EC Declaration of Conformity

Makita declares that the following Machine(s):

Designation of Machine:

Cordless Hedge Trimmer

Model No./Type: DUH481, DUH483, DUH521,

DUH523

Specifications: see “SPECIFICATIONS” table.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DUH523 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 6,34 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DUH523 Manual

Product: