Manual Makita DUC405Z (page 16 of 128) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

711173

Zoom out

Zoom in

1/128

16 ENGLISH

Carrying tool

Before carrying the tool, always apply the chain brake

and remove the battery cartridges from the tool. Then

attach the guide bar cover. Also cover the battery car-

tridge with the battery cover.

►Fig.29: 1. Guide bar cover 2. Battery cover

MAINTENANCE

CAUTION:

Always be sure that the tool is

switched off and the battery cartridge is removed before

attempting to perform inspection or maintenance.

CAUTION: Always wear gloves when perform-

ing any inspection or maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

To maintain product SAFETY and RELIABILITY,

repairs,anyothermaintenanceoradjustmentshould

be performed by Makita Authorized or Factory Service

Centers, always using Makita replacement parts.

Sharpening the saw chain

Sharpen the saw chain when:

•

Mealy sawdust is produced when damp wood is cut;

• Thechainpenetratesthewoodwithdifculty,even

when heavy pressure is applied;

• The cutting edge is obviously damaged;

• The saw pulls to the left or right in the wood.

(caused by uneven sharpening of the saw chain or

damage to one side only)

Sharpen the saw chain frequently but a little each time.

Twoorthreestrokeswithaleareusuallysufcientfor

routine resharpening. When the saw chain has been

resharpened several times, have it sharpened in our

authorized service center.

Sharpening criteria:

WARNING: An excessive distance between

the cutting edge and depth gauge increases the

risk of kickback.

►Fig.30: 1. Cutter length 2. Distance between cutting

edge and depth gauge 3. Minimum cutter

length (3 mm)

— All cutter length must be equal. Different cutter

lengths prevent the saw chain from running

smoothly and may cause the saw chain to break.

— Do not sharpen the chain when the cutter length

has reached 3 mm or shorter. The chain must be

replaced with new one.

—

The chip thickness is determined by the distance between

the depth gauge (round nose) and the cutting edge.

— The best cutting results are obtained with following

distance between cutting edge and depth gauge.

• Chainblade90PX:0.65mm(0.025″)

• Chainblade91PX:0.65mm(0.025″)

►Fig.31

— The sharpening angle of 30° must be the same on

all cutters. Different cutter angles cause the chain

to run roughly and unevenly, accelerate wear, and

lead to chain breaks.

— Useasuitableroundlesothatthepropersharp-

ening angle is kept against the teeth.

• Chain blade 90PX : 55°

• Chain blade 91PX : 55°

File and le guiding

— Useaspecialroundle(optionalaccessory)for

saw chains to sharpen the chain. Normal round

lesarenotsuitable.

— Diameteroftheroundleforeachsawchainisas

follows:

• Chainblade90PX:4.5mm(3/16″)

• Chainblade91PX:4.0mm(5/32″)

— Theleshouldonlyengagethecutteronthefor-

wardstroke.Lifttheleoffthecutteronthereturn

stroke.

— Sharpentheshortestcutterrst.Thenthelength

of this shortest cutter becomes the standard for all

other cutters on the saw chain.

— Guidetheleasshowninthegure.

►Fig.32: 1. File 2. Saw chain

—

Thelecanbeguidedmoreeasilyifaleholder

(optionalaccessory)isemployed.Theleholderhas

markings for the correct sharpening angle of 30° (align

the markings parallel to the saw chain) and limits the

depthofpenetration(to4/5ofthelediameter).

►Fig.33: 1. File holder

— After sharpening the chain, check the height of the

depth gauge using the chain gauge tool (optional

accessory).

►Fig.34

— Removeanyprojectingmaterial,howeversmall,

withaspecialatle(optionalaccessory).

— Round off the front of the depth gauge again.

Cleaning the guide bar

Chips and sawdust will build up in the guide bar groove.

Theymayclogthebargrooveandimpairtheoilow.

Clean out the chips and sawdust every time when you

sharpen or replace the saw chain.

►Fig.35

Cleaning the sprocket cover

Chips and saw dust will accumulate inside of the

sprocket cover. Remove the sprocket cover and saw

chain from the tool then clean the chips and saw dust.

►Fig.36

Cleaning the oil discharge hole

Small dust or particles may be built up in the oil dis-

charge hole during operation. These dust or particles

mayimpairtheoiltoowandcauseaninsufcient

lubrication on the whole saw chain. When a poor chain

oil delivery occurs at the top of guide bar, clean the oil

discharge hole as follows.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DUC405Z in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 31,22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DUC405Z Manual

Product: