Manual Makita DUC353 (page 16 of 128) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

690908

Zoom out

Zoom in

1/128

16 ENGLISH

— The sharpening angle of 30° must be the same on

all cutters. Different cutter angles cause the chain

to run roughly and unevenly, accelerate wear, and

lead to chain breaks.

— Useasuitableroundlesothatthepropersharp-

ening angle is kept against the teeth.

• Chainblade90PX:55°

• Chainblade91PX:55°

File and le guiding

— Useaspecialroundle(optionalaccessory)for

saw chains to sharpen the chain. Normal round

lesarenotsuitable.

— Diameteroftheroundleforeachsawchainisas

follows:

• Chainblade90PX:4.5mm(3/16″)

• Chainblade91PX:4.0mm(5/32″)

— Theleshouldonlyengagethecutteronthefor-

wardstroke.Lifttheleoffthecutteronthereturn

stroke.

— Sharpentheshortestcutterrst.Thenthelength

of this shortest cutter becomes the standard for all

other cutters on the saw chain.

— Guidetheleasshowninthegure.

►Fig.35: 1. File 2. Saw chain

— Thelecanbeguidedmoreeasilyifaleholder

(optionalaccessory)isemployed.Theleholder

has markings for the correct sharpening angle of

30° (align the markings parallel to the saw chain)

and limits the depth of penetration (to 4/5 of the

lediameter).

►Fig.36: 1. File holder

— Aftersharpeningthechain,checktheheightofthe

depth gauge using the chain gauge tool (optional

accessory).

►Fig.37

— Removeanyprojectingmaterial,howeversmall,

withaspecialatle(optionalaccessory).

— Round off the front of the depth gauge again.

Cleaning the guide bar

Chips and sawdust will build up in the guide bar groove.

Theymayclogthebargrooveandimpairtheoilow.

Clean out the chips and sawdust every time when you

sharpen or replace the saw chain.

►Fig.38

Cleaning the sprocket cover

Chips and saw dust will accumulate inside of the

sprocket cover. Remove the sprocket cover and saw

chain from the tool then clean the chips and saw dust.

►Fig.39

Cleaning the oil discharge hole

Small dust or particles may be built up in the oil dis-

charge hole during operation. These dust or particles

mayimpairtheoiltoowandcauseaninsufcient

lubricationonthewholesawchain.Whenapoorchain

oil delivery occurs at the top of guide bar, clean the oil

discharge hole as follows.

1. Remove the sprocket cover and saw chain from

the tool.

2. Remove the small dust or particles using a slotted

screwdriver with a slender shaft or the like.

►Fig.40: 1. Slotted screwdriver 2. Oil discharge hole

3. Insert the battery cartridge into the tool. Pull the

switchtriggertoowbuilt-updustorparticlesofftheoil

discharge hole by discharging chain oil.

4. Remove the battery cartridge from the tool.

Reinstall the sprocket cover and saw chain on the tool.

Replacing the sprocket

CAUTION: A worn sprocket will damage a

new saw chain. Have the sprocket replaced in this

case.

Beforettinganewsawchain,checktheconditionof

the sprocket.

►Fig.41: 1. Sprocket 2.Areastobewornout

Alwaystanewlockingringwhenreplacingthe

sprocket.

►Fig.42: 1. Locking ring 2. Sprocket

NOTICE: Make sure that the sprocket is installed

as shown in the gure.

Storing the tool

1. Clean the tool before storing. Remove any chips

and sawdust from the tool after removing the sprocket

cover.

2. Aftercleaningthetool,runitundernoloadtolubri-

cate the saw chain and guide bar.

3. Cover the guide bar with the guide bar cover.

4. Emptytheoiltank.

I have a Makita duc353 chainsaw and would like to disable to auto off function. Can this be done? Cheers Submitted on 31-10-2022 at 05:25
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DUC353 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 30,8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DUC353 Manual

Product: