Manual Makita DTS141 (page 8 of 72) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

600212

Zoom out

Zoom in

1/72

The impact force can be changed in four steps: hard,

medium, soft, and T mode.

This allows a tightening suitable to the work.

Every time the button is pressed, the number of

blows changes in four steps.

For approximately one minute after releasing the switch

trigger, the impact force can be changed.

“T” is a special mode for fastening self drilling screws and

bolts. In this mode, the tool starts to drive a screw with

faster rotation, which is suited for drilling with the self-

drilling-screw tip. Once the tool starts to tighten the

screw, it impacts in soft force grade.

NOTE:

• When all lamps on the switch panel go out, the tool is

turned off to save the battery power. The impact force

grade can be checked by pulling the switch trigger to

the extent that the tool does not operate.

• While pulling the switch trigger, the impact force grade

cannot be changed.

• The tool automatically stops to prevent the damages on

the parts during heavy load operation with hard or

medium impact force grade. In that case select the soft

or T mode impact force grade.

Indicating the remaining battery capacity (Fig. 8)

(Country specific)

When you pull the switch trigger, the LED display shows

the remaining battery capacity.

The remaining battery capacity is shown as the following

table.

015191

NOTE:

• Approximately one minute after the motor stops, the

indicators go off to save the battery power. To check

the remaining battery capacity, slightly pull the switch

trigger.

Tool / battery protection system

The tool is equipped with a tool/battery protection

system. This system automatically cuts off power to the

motor to extend tool and battery life.

The tool will automatically stop during operation if the

tool or battery are placed under one of the following

conditions. In some conditions, the indicator lights up.

Overload protection

When the tool is operated in a manner that causes it to

draw an abnormally high current, the tool automatically

stops without any indications. In this situation, turn the

tool off and stop the application that caused the tool to

become overloaded. Then turn the tool on to restart.

Overheat protection for tool

When the tool is overheated, the tool stops automatically

and the battery indicator shows following state. In this

situation, let the tool cool before turning the tool on again.

015192

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

Installing or removing driver bit or socket bit

(Fig. 9)

Use only bits that has inserting portion shown in the

figure.

For tool with shallow bit hole

006348

For tool with deep bit hole

011405

Procedure 1 (Fig. 10)

For tool with normal sleeve

To install the bit, pull the sleeve in the direction of the

arrow and insert the bit into the sleeve as far as it will go.

Then release the sleeve to secure the bit.

For tool with one-touch type sleeve

To install the bit, insert the bit into the sleeve as far as it

will go.

Procedure 2 (Fig. 11)

In addition to the procedure (1) above, insert the bit-

piece into the sleeve with its pointed end facing in.

To remove the bit, pull the sleeve in the direction of the

arrow and pull the bit out.

Battery indicator status

Remaining battery

capacity

: On : Off : Blinking

50% – 100%

20% – 50%

0% – 20%

Charge the

battery

Battery

indicator

: On : Off : Blinking

Tool is overheated

A = 12 mm

B = 9 mm

Use only these type of bit. Follow the

procedure (1).

(Note) Bit-piece is not necessary.

A = 17 mm

B = 14 mm

To install these types of bits, follow the

procedure (1).

A = 12 mm

B = 9 mm

To install these types of bits, follow the

procedure (2).

(Note) Bit-piece is necessary for

installing the bit.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DTS141 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 3,95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DTS141 Manual

Product: