Manual Makita DTD170 (page 9 of 76) (English, German, Dutch, Danish, French, Italian, Portuguese, Portuguese, Spanish)

657996

Zoom out

Zoom in

1/76

9 ENGLISH

Procedure 2

In addition to Procedure 1, insert the bit-piece into the

sleeve with its pointed end facing in.

►Fig.13: 1. Driver bit 2. Bit-piece 3. Sleeve

To remove the driver bit, pull the sleeve in the direction

of the arrow and pull the driver bit out.

NOTE: If the driver bit is not inserted deep enough

into the sleeve, the sleeve will not return to its original

position and the driver bit will not be secured. In this

case, try re-inserting the bit according to the instruc-

tions above.

NOTE:Whenitisdifculttoinsertthedriverbit,pull

the sleeve and insert it into the sleeve as far as it will

go.

NOTE:Afterinsertingthedriverbit,makesurethatit

isrmlysecured.Ifitcomesout,donotuseit.

Installing hook

►Fig.14: 1. Groove 2. Hook 3. Screw

The hook is convenient for temporarily hanging the tool.

This can be installed on either side of the tool. To install

the hook, insert it into a groove in the tool housing on

either side and then secure it with a screw. To remove,

loosen the screw and then take it out.

OPERATION

►Fig.15

The proper fastening torque may differ depending upon

thekindorsizeofthescrew/bolt,thematerialofthe

workpiece to be fastened, etc. The relation between fas-

teningtorqueandfasteningtimeisshowninthegures.

Proper fastening torque for standard bolt

N•m

(kgf•cm)

M14

M12

M10

M16

M14

M12

M10

M16

140

(1428)

(1224)

(1020)

(816)

(612)

(408)

(204)

120

100

1. Fastening time (second) 2. Fastening torque

Proper fastening torque for high tensile bolt

M14

M12

M14

M12

M10

200

180

160

140

120

100

0123

(2040)

(1836)

(1632)

(1428)

(1224)

(1020)

(816)

(612)

(408)

(204)

N•m

(kgf•cm)

1. Fastening time (second) 2. Fastening torque

Holdthetoolrmlyandplacethepointofthedriverbit

inthescrewhead.Applyforwardpressuretothetoolto

the extent that the bit will not slip off the screw and turn

the tool on to start operation.

NOTICE: If you use a spare battery to continue

the operation, rest the tool at least 15 min.

NOTE:Usetheproperbitfortheheadofthescrew/

bolt that you wish to use.

NOTE:WhenfasteningM8orsmallerscrew,carefully

adjustpressureontheswitchtriggersothatthescrew

is not damaged.

NOTE: Hold the tool pointed straight at the screw.

NOTE: If the impact force is too strong or you tighten

thescrewforatimelongerthanshowninthegures,

the screw or the point of the driver bit may be over-

stressed, stripped, damaged, etc. Before starting your

job,alwaysperformatestoperationtodeterminethe

proper fastening time for your screw.

The fastening torque is affected by a wide variety of

factorsincludingthefollowing.Afterfastening,always

check the torque with a torque wrench.

1. Whenthebatterycartridgeisdischargedalmost

completely, voltage will drop and the fastening

torque will be reduced.

2. Driver bit or socket bit

Failure to use the correct size driver bit or socket

bit will cause a reduction in the fastening torque.

3. Bolt

• Eventhoughthetorquecoefcientandthe

class of bolt are the same, the proper fasten-

ing torque will differ according to the diame-

ter of bolt.

• Eventhoughthediametersofboltsarethe

same, the proper fastening torque will differ

accordingtothetorquecoefcient,theclass

of bolt and the bolt length.

4. The manner of holding the tool or the material

of driving position to be fastened will affect the

torque.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DTD170 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Portuguese, Spanish as an attachment in your email.

The manual is 18,76 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DTD170 Manual

Product: