Manual Makita DTD154 (page 8 of 68) (English, German, Dutch, Danish, French, Italian, Portuguese, Portuguese, Spanish)

657995

Zoom out

Zoom in

1/68

8 ENGLISH

Lighting up the front lamp

CAUTION: Do not look in the light or see the

source of light directly.

►Fig.5: 1. Lamp

►Fig.6: 1. Button

Pulltheswitchtriggertoturnonthelamp.Toturnoff,

release it. The lamp goes out approximately 10 seconds

after releasing the switch trigger.

To keep the lamp off, turn off the lamp status. To turn off

thelampstatus,rstpullandreleasetheswitchtrigger.

Andthenpressthebutton

for one second within 10

seconds.

To turn on the lamp status again, press the button again

similarly.

NOTE:Toconrmthelampstatus,pullthetrigger.

Whenthelamplightsupbypullingtheswitchtrigger,

thelampstatusisON.Whenthelampdoesnotcome

on, the lamp status is OFF.

NOTE:Whenthetoolisoverheated,thelightashes

foroneminute,andthentheLEDdisplaygoesoff.In

this case, cool down the tool before operating again.

NOTE: Use a dry cloth to wipe the dirt off the lens of

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

Reversing switch action

►Fig.7: 1. Reversing switch lever

CAUTION: Always check the direction of

rotation before operation.

CAUTION: Use the reversing switch only after

the tool comes to a complete stop. Changing the

direction of rotation before the tool stops may dam-

age the tool.

CAUTION: When not operating the tool,

always set the reversing switch lever to the neu-

tral position.

This tool has a reversing switch to change the direction

of rotation. Depress the reversing switch lever from the

AsideforclockwiserotationorfromtheBsideforcoun-

terclockwise rotation.

Whenthereversingswitchleverisintheneutralposi-

tion, the switch trigger cannot be pulled.

Changing the impact force

►Fig.8: 1. Changed in four steps 2. Hard 3. Medium

4. Soft 5. T mode 6. Button

Youcanchangetheimpactforceinfoursteps:hard,medium,soft,andTmode.

This allows a tightening suitable to the work.

Everytimethebutton

is pressed, the number of blows changes in four steps.

“T” is a special mode for fastening self drilling screws. In this mode, the tool starts to drive a screw with faster rota-

tion, which is suited for drilling with the self-drilling-screw tip. Once the tool starts to tighten the screw, it impacts in

medium force grade.

For approximately one minute after releasing the switch trigger, the impact force can be changed.

Impact force grade displayed

on panel

Maximum blows Purpose Example of application

Hard

TS H

3,800 min

-1

(/min) Tightening when force and

speed are desired.

Tightening underwork mate-

rials, tightening long screws,

tightening bolts.

Medium

TS H

2,600 min

-1

(/min) Tighteningwhenagoodnish-

ing is needed.

Tighteningnishingboards,

plaster boards.

Soft

TS H

1,100 min

-1

(/min) Tightening with less force to

avoid screw thread breakage.

Tightening sash screws, tight-

ening small screws such as M6.

T mode

TS H

2,600 min

-1

(/min) Tightening when speed and

goodnishingareneeded.

Tightening self drilling screws.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DTD154 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Portuguese, Spanish as an attachment in your email.

The manual is 11,7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DTD154 Manual

Product: