600224

Makita DTD136 Manual

8
Zoom out
Zoom in
Previous page
1/64
Next page
8
Changing the impact force (Fig. 8)
013975
The impact force can be changed in four steps: hard,
medium, soft, and T mode.
This allows a tightening suitable to the work.
Every time the button is pressed, the number of blows
changes in four steps.
“T” is a special mode for fastening self drilling screws. In
this mode, the tool starts to drive a screw with faster rota-
tion, which is suited for drilling with the self-drilling-screw
tip. Once the tool starts to tighten the screw, it impacts in
medium force grade.
For approximately one minute after releasing the switch
trigger, the impact force can be changed.
NOTE:
• When all lamps on the switch panel go out, the tool is
turned off to save the battery power. The impact force
grade can be checked by pulling the switch trigger to
the extent that the tool does not operate.
• While pulling the switch trigger, the impact force grade
cannot be changed.
Indicating the remaining battery capacity (Fig. 9)
(Country specific)
When you pull the switch trigger, the LED display shows
the remaining battery capacity.
The remaining battery capacity is shown as the following
table.
012273
NOTE:
• When the LED display goes off, the tool is turned off to
save the battery power. To check the remaining battery
capacity, slightly pull the switch trigger.
• The LED display goes off approximately one minute
after releasing the switch trigger.
• When the tool is overheated, the light flashes once per
second for one minute, and then the LED display goes
off. In this case, cool down the tool before operating
again.
• When the LED display lights up and the tool stops even
with a recharged battery cartridge, cool down the tool
fully. If the status will not change, stop using and have
the tool repaired by a Makita local service center.
Impact force grade
displayed on panel
Maximum blows
Application Work
DTD136 DTD147
Hard
3,200
(min
–1
)
3,400
(min
–1
)
Tightening when force and
speed are desired.
Tightening in underwork
material/Tightening long
screws/Tightening bolts.
Medium
2,600
(min
–1
)
2,800
(min
–1
)
Tightening when a good
finishing is needed.
Tightening in the finishing
board, plaster board.
Soft
1,100
(min
–1
)
1,300
(min
–1
)
Tightening when excessive
tightening need to be avoided
because of potentially
clogged female screw and
broken or damaged screw
head.
Tightening sash screw/
Tightening small screws such
as M6.
T mode
2,600
(min
–1
)
2,800
(min
–1
)
Tightening when speed and
good finishing are needed.
Tightening self drilling screws.
LED indicator status Remaining battery capacity
About 50% or more
About 20% – 50%
About less than 20%
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DTD136 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DTD136 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 1,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info