Manual Makita DST221 (page 6 of 44) (English, German, Polish)

600230

Zoom out

Zoom in

1/44

CAUTION:

• Do not use staples other than designated in this

manual or staples that appear to be damaged, bent,

rusty or corroded.

• Do not insert staples of which size is different each

other at the same time inside the magazine ,

causing poor staple feed or jamming.

Loading staples

Remove the battery cartridge.

Press the locking lever on the rear of the sub magazine

and slide the sub magazine backward.

Fig.3

Load staples into the main magazine with their feet

facing up. Slide the sub-magazine forward.

Fig.4

To secure the sub magazine in place, hook the locking

lever on the rear of the sub-magazine.

CAUTION:

• With the magazine loaded, if the tool is held

downward and the sub-magazine is opened, the

staples can fall out and present a danger to anyone

or anything below. Keep this in mind especially

when working in high locations.

Unloading staples

CAUTION:

•

When removing staples, make sure that your fingers

are not placed on the trigger or the lever and the battery

cartridge is removed from the stapler. Misfiring may

cause personal injuries and property damage.

Remove the battery cartridge.

Press the locking lever and slide the magazine back.

Fig.5

Take out staples from the magazine slit.

Fig.6

Hook

CAUTION:

• Always make sure that your fingers are not placed

on the trigger or the lever and the battery cartridge

is removed before using the hook.

Fig.7

CAUTION:

• Do not hang the hook from the waist belt. Dropping

the stapler, which is caused by the hook

accidentally coming out of place, may cause

misfiring and personal injuries.

The hook is convenient for temporarily hanging the tool.

This can be installed on either side of the tool.

To install the hook, insert it into a groove in the tool

housing on either side and then secure it with a screw. To

remove, loosen the screw and then take it out.

Fig.8

OPERATION

Depth adjustment

Fig.9

If the staples are driven too deep or too shallow, adjust

the driving depth by turning the nut on the bottom of the

tool. For deeper driving of staples, turn the nut clockwise.

For shallower driving, turn the nut counterclockwise.

Please note the nut must be turned in increments of 90°

(1/4 turn) so that the groove on the nut runs parallel to the

magazine.

Driving staples

Fig.10

Place flat the opening of the tool from which staples are

fired on the material to be fastened and hold the tool

firmly against the material. Then pull the lever and then

pull the trigger fully to drive the staples. The grip is

shaped so that the tool head can be held down securely

with index finger and thumb. After driving a staple, be

sure to release the trigger fully.

When the head of driven staple remains above the

surface of material to be fastened, drive the staple while

holding the stapler head firmly.

Fig.11

NOTE:

• Using the stapler continuously with the head of

driven staples remaining above the surface of

material to be fastened may cause damage to the

driver of the stapler and stapler jamming etc..

Checking remaining staples

Fig.12

CAUTION:

• Do not operate the tool without staples. It shortens

the service life of the tool.

There is a convenient sight window on the right side of

the tool (when viewing the tool from the front). Use this

sight window to check if there are staples in the

magazine. When staples are not visible through the

window, load staples into the magazine.

Removing jammed staples

WARNING:

• Always make sure that the trigger are released and

the battery cartridge is removed before removing

jammed staples .

Remove the battery cartridge from the stapler.

Fig.13

Press the locking lever on the rear of the sub magazine

and slide the sub magazine backward.

Take out stuck staples that remain inside the opening

that staples are fired from as it appears.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DST221 in the language / languages: English, German, Polish as an attachment in your email.

The manual is 2,16 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DST221 Manual

Product: