711195

Makita DSL800ZU Manual

14
Zoom out
Zoom in
Previous page
1/124
Next page
14 ENGLISH
Installing the abrasive disc
►Fig.10: 1.Abrasivedisc2. Pad
Removeanydirtorforeignmatterfromthepad,and
thenattachtheabrasivedisctothepadwhilealigning
theholesintheabrasivediscwiththoseinthepad.
Adjusting the pipe length
CAUTION: When adjusting the pipe length,
hold the tool horizontally. Otherwise, the pipe
lengthmaychangeunintentionallyanditmaycause
aninjuryormalfunctionofthetool.
NOTICE: Do not extend the pipe beyond the
limit.Failuretodosomaycauseamalfunctionof
the tool.
►Fig.11: 1. Sleeve 2. Pipe
Toadjustthepipelength,loosenthesleeve,thenadjust
the length of the pipe, and then tighten the sleeve.
Installing or removing the dust
collection brush
Before sanding operation, install the dust collection
brushtothesandingheadasshowninthegure.
►Fig.12: 1.Dustcollectionbrush2. Sanding head
Youcanremovethedustcollectionbrushforoperation
alongtheedgeofwallorceiling.Theremovedbrush
canbeattachedtothesandingheadasshowninthe
gure.
►Fig.13: 1.Dustcollectionbrush2. Sanding head
Hex wrench storage
►Fig.14: 1. Hex wrench
When not in use, store the hex wrench as shown in the
guretokeepitfrombeinglost.
Installing or removing the pad
►Fig.15: 1. Hex wrench 2. Bolt 3. Pad
Toremovethepad,removetheabrasivediscfromthe
pad,andthenturntheboltcounterclockwisewithahex
wrench. To install the pad, perform the removal proce-
dure in reverse.
CAUTION: Make sure that the pad is secured
properly.Looseattachmentwillrunoutofbalance
andcauseanexcessivevibrationwhichmaycause
loss of control.
Connecting a vacuum cleaner
Optional accessory
Whenyouwishtoperformoperationcleanly,connecta
Makitavacuumcleanertoyourtool.Connectahoseof
the vacuum cleaner to the dust nozzle using the front
cuff 24.
►Fig.16: 1. Hose of the vacuum cleaner 2.Frontcuff
24 3. Dust nozzle
Installing or removing the extension handle
Optional accessory
To install the extension handle, attach the extension handle to the
toolandsecureitwiththeknobrmly.Besuretoinserttheend
of the tool into the holder of the extension handle. To remove the
extension handle, perform the installation procedure in reverse.
►Fig.17:
1.Extensionhandle2.Knob3. Holder 4.Endoftool
OPERATION
CAUTION: Only use Makita genuine pads for
sanding (optional accessories).
CAUTION:
Make sure the work material is secured
and stable. Falling object may cause personal injury.
CAUTION: Hold the tool rmly with one hand
on the switch handle and the other hand on the
front grip when operating the tool.
CAUTION:
Do not run the tool at high load over
an extended time period.Itmayresultintoolmalfunction
whichcauseselectricshock,reand/orseriousinjury.
CAUTION:
Be careful not to touch the rotating part.
NOTICE: Never force the tool. Excessivepressure
mayleadtodecreasedsandingefciency,damaged
pad, or shorten tool life.
NOTICE: Continuous operation at high speed
may damage work surface.
1. Positionthetoollightlyagainsttheworksurface.
Applylightpressureenoughtoalignthesandinghead
with the work surface.
2.
Applyadditionalpressuretoengagethepadonthe
work surface. Move the tool in an overlapping pattern in
constantmotiontosmooththedrywallcompound.
►Fig.18
Operating the tool with the extension handle
Optional accessory
CAUTION:
Hold the tool rmly with one hand on the
switch handle and the other hand on the extension handle
when operating the tool with the extension handle.
1.
Wearthebeltfortheextensionhandleasshowninthegure.
►Fig.19: 1. Belt
2. Attachtheholdertothebelt.
►Fig.20: 1. Holder 2. Belt
3. Put the end of the extension handle into the holder
to support the tool.
►Fig.21: 1.Endofextensionhandle2. Holder
Operatethetoolinthesamewayasthetoolwithoutthe
extension handle.
►Fig.22
Youcanalsooperatethetoolwithoutusingthebeltand
theholderasshowninthegure.
►Fig.23
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DSL800ZU at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DSL800ZU in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 17,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info