Manual Makita DSL800ZU (page 10 of 124) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

711195

Zoom out

Zoom in

1/124

10 ENGLISH

SAFETY WARNINGS

General power tool safety warnings

WARNING: Read all safety warnings, instruc-

tions, illustrations and specications provided

with this power tool.Failuretofollowallinstructions

listedbelowmayresultinelectricshock,reand/or

seriousinjury.

Save all warnings and instruc-

tions for future reference.

Theterm"powertool"inthewarningsreferstoyour

mains-operated(corded)powertoolorbattery-operated

(cordless) power tool.

Cordless drywall sander safety warnings

Safety Warnings Common for Sanding Operations:

This power tool is intended to function as a sander.

Read all safety warnings, instructions, illustrations

and specications provided with this power tool.

Failuretofollowallinstructionslistedbelowmayresult

inelectricshock,reand/orseriousinjury.

Operations such as grinding, wire brushing,

polishing or cutting-off are not recommended

to be performed with this power tool. Operations

forwhichthepowertoolwasnotdesignedmay

createahazardandcausepersonalinjury.

Do not use accessories which are not specically

designed and recommended by the tool manufac-

turer.Justbecausetheaccessorycanbeattachedto

yourpowertool,itdoesnotassuresafeoperation.

4. The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool.Accessoriesrunningfasterthan

theirratedspeedcanbreakandyapart.

5. The outside diameter and the thickness of your

accessory must be within the capacity rating

of your power tool.Incorrectlysizedaccessories

cannotbeadequatelyguardedorcontrolled.

6.

Do not use a damaged accessory. Before each

use inspect the accessory such as pad for cracks,

tear or excess wear. If power tool or accessory is

dropped, inspect for damage or install an undam-

aged accessory. After inspecting and installing

an accessory, position yourself and bystanders

away from the plane of the rotating accessory and

run the power tool at maximum no-load speed

for one minute.Damagedaccessorieswillnormally

breakapartduringthistesttime.

7. Wear personal protective equipment.

Depending on application, use face shield,

safety goggles or safety glasses. As appro-

priate, wear dust mask, hearing protectors,

gloves and workshop apron capable of stop-

ping small abrasive or workpiece fragments.

Theeyeprotectionmustbecapableofstopping

yingdebrisgeneratedbyvariousoperations.

Thedustmaskorrespiratormustbecapableof

ltratingparticlesgeneratedbyyouroperation.

Prolongedexposuretohighintensitynoisemay

cause hearing loss.

Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment.Fragmentsof

workpieceorofabrokenaccessorymayyawayand

causeinjurybeyondimmediateareaofoperation.

9. Position the cord clear of the spinning acces-

sory.Ifyoulosecontrol,thecordmaybecutor

snaggedandyourhandorarmmaybepulledinto

thespinningaccessory.

10. Never lay the power tool down until the acces-

sory has come to a complete stop. The spinning

accessorymaygrabthesurfaceandpullthe

powertooloutofyourcontrol.

11. Do not run the power tool while carrying it at

your side.Accidentalcontactwiththespinning

accessorycouldsnagyourclothing,pullingthe

accessoryintoyourbody.

12. Do not operate the power tool near ammable

materials. Sparks could ignite these materials.

13. Do not use accessories that require liquid

coolants.Usingwaterorotherliquidcoolants

mayresultinelectrocutionorshock.

Kickback and Related Warnings

Kickbackisasuddenreactiontoapinchedorsnaggedrotat-

ingpadoranyotheraccessory.Pinchingorsnaggingcauses

rapidstallingoftherotatingaccessorywhichinturncauses

theuncontrolledpowertooltobeforcedinthedirectionoppo-

siteoftheaccessory’srotationatthepointofthebinding.

Forexample,ifapadissnaggedorpinchedbythe

workpiece, the edge of the pad that is entering into the

pinch point can dig into the surface of the material caus-

ingthepadtoclimboutorkickout.Thepadmayeither

jumptowardorawayfromtheoperator,dependingon

directionofthepad’smovementatthepointofpinching.

Padmayalsobreakundertheseconditions.

Kickbackistheresultofpowertoolmisuseand/or

incorrectoperatingproceduresorconditionsandcanbe

avoidedbytakingproperprecautionsasgivenbelow.

Maintain a rm grip on the power tool and position

your body and arm to allow you to resist kickback

forces. Always use auxiliary handle, if provided, for

maximum control over kickback or torque reaction

during start-up.Theoperatorcancontroltorquereac-

tionsorkickbackforces,ifproperprecautionsaretaken.

2. Never place your hand near the rotating acces-

sory.Accessorymaykickbackoveryourhand.

3. Do not position your body in the area where

power tool will move if kickback occurs.

Kickbackwillpropelthetoolindirectionopposite

tothewheel’smovementatthepointofsnagging.

4. Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory.Corners,sharpedgesorbouncing

haveatendencytosnagtherotatingaccessory

andcauselossofcontrolorkickback.

5. Do not attach a saw chain woodcarving blade

or toothed saw blade.Suchbladescreatefre-

quentkickbackandlossofcontrol.

Safety Warnings Specic for Sanding Operations:

1. Do not use excessively oversized sanding

disc paper. Follow manufacturers recommen-

dations, when selecting sanding paper. Larger

sandingpaperextendingbeyondthesanding

padpresentsalacerationhazardandmaycause

snagging,tearingofthediscorkickback.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DSL800ZU in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 17,71 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DSL800ZU Manual

Product: