657238

Makita DSD180 Manual

8
Zoom out
Zoom in
Previous page
1/64
Next page
8 ENGLISH
Switch action
►Fig.5: 1. Switch trigger
CAUTION: Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
Tostartthetool,simplypulltheswitchtrigger.Tool
speed is increased by increasing pressure on the switch
trigger. Release the switch trigger to stop.
Thetriggercanbelockedofftopreventitfrombeing
pulledaccidentally.Tolockthetriggeroff,pressthe
button from the side with
marking.Tounlock,press
the button from the side with marking.
►Fig.6: 1. Lock-off button
CAUTION: Always lock the tool off when
carrying or suspending the operation.
Adjusting depth of cut
Thecuttingdepthcorrespondswiththescaleonthe
blade. Loosen the screw on the blade holder until the
bladecanmovefreely.Alignthescaleonthebladewith
thebottomlineofthebladeholder.Thentightenthe
screws.
►Fig.7: 1. Cutting depth 2. Bottom line of the blade
holder 3. Scale on the blade
Themaximumcuttingdepthdependsonthetypeof
thesawblade.Alwaysusethesawbladedesignedfor
cutting the working material.
Type of saw blade Max. cutting depth
For drywall 30 mm
For wood 15 mm
LED light
CAUTION: Do not look in the light or see the
source of light directly.
Pulltheswitchtriggertolightupthelamp.Thelamp
keeps on lighting while the switch trigger is being pulled.
Thelampgoesoutapproximately10secondsafter
releasing the trigger.
►Fig.8: 1. Lamp
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Removing the dust collector
CAUTION: Never operate the tool without the
dust collector. Dust may come into your eyes and
causeeyeinjury.
Toremovethedustcollector,holdthetoolhandleand
pull back the tabs on the tool. Be sure to pull the tabs on
the both sides at the same time.
►Fig.9: 1.Tab
When installing, align the dust collector's edge with the
groove on the base.
►Fig.10: 1. Groove
Replacing drywall saw blade
CAUTION: Always clean out all chips or for-
eign matter adhering to the blade and/or blade
holder.Failuretodosomaycauseinsufcienttight-
ening of the blade, resulting in a serious personal
injury.
CAUTION: Do not touch the blade or the
workpiece immediately after operation.Theymay
be extremely hot and could burn your skin.
CAUTION: Make sure that the blade is prop-
erly secured. Insufcienttighteningoftheblademay
causebladebreakageorseriouspersonalinjury.
1. Remove the dust collector.
2. Remove the bolts on the blade holder with the hex
wrench.
►Fig.11: 1. Bolts 2. Blade holder 3. Blade
3. Setanewbladeasshowninthegure.Makesure
that the curved edge of the blade points forward. Fit the
protrusion of the blade holder into the slot on the blade.
►Fig.12: 1. Slot 2.Protrudedportion(oppositeside)
4. Adjustthecuttingdepththentightenthebolts.
5. Attachthedustcollector.
Installing snap-off blade
CAUTION: Always use the snap-off blade with
designated length, width, and thickness.Aninap-
propriatelyinstalledsnap-offbladecanbebroken.A
brokenbladecanyoffandcauseapersonalinjury.
Asnap-offbladecanalsobeusedwiththistool.Use3
segments of 18 mm wide snap-off blade with 0.5 mm
thickness.Themaximumcuttingdepthis12.5mm
when cutting a drywall.
►Fig.13: 1.Threesegmentsofsnap-offblade
1. Loosentheboltsonthebladeholder.Turnthe
blade holder so that its protrusion faces outward.
2. Insertthesnap-offbladesothatthesharpedge
faces forward.
3. Secure the snap-off blade at the position where
theendoftherstsegmentcomestotheedgeofblade
holder as illustrated.
►Fig.14: 1. Blade holder 2.Endoftherstsegment
of snap-off blade 3.Allowablecuttinglength
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DSD180 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DSD180 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Portuguese, Spanish as an attachment in your email.

The manual is 15,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info