Manual Makita DSC250 (page 10 of 24) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691889

Zoom out

Zoom in

1/24

10 ENGLISH

Installing or removing battery

cartridge

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge. Failure to hold the tool and the battery

cartridge rmly may cause them to slip off your hands

and result in damage to the tool and battery cartridge

and a personal injury.

► Fig.2: 1. Button 2. Red indicator 3. Battery cartridge

To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator on the

upper side of the button, it is not locked completely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

it may accidentally fall out of the tool, causing injury to

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

Battery protection system (Lithium-

ion battery with star marking)

► Fig.3: 1. Star marking

Lithium-ion batteries with a star marking are equipped

with a protection system. This system automatically

cuts off power to the tool to extend battery life. The tool

will automatically stop during operation if the tool and/or

battery are placed under one of the following conditions:

Overloaded:

The tool is operated in a manner that causes it to draw

an abnormally high current. In this situation, release the

trigger switch on the tool and stop the application that

caused the tool to become overloaded. Then pull the

trigger switch again to restart. If the tool does not start,

the battery is overheated. In this situation, let the bat-

tery cool before pulling the trigger switch again.

Low battery voltage:

The remaining battery capacity is too low and the tool

will not operate. In this situation, remove and recharge

the battery.

OPERATING

PROCEDURE

WARNING: Before the battery is inserted into

the tool, ensure that the Switch is at the “O” posi-

tion and the Switch is off.

CAUTION: Push the Lock Button and ensure

that the Button comes up when it is released.

If the Lock Button will not come up when it is

released, the Tipped Saw will be prevented from

rotating when the tool is operated resulting in

damage to parts and the motor to burn out.

CAUTION: Slide the Switch to the “l” posi-

tion and ensure it stays there and does not move.

Then push down on the rear of the Switch to

ensure that the Switch moves to the “O” position

automatically.

CAUTION: Ensure that the bolts retaining the

Tipped Saw Cover and all other bolts are tight-

ened rmly.

► Fig.4: 1. Handle Position (parallel / left side) 2. Lock

Button 3. Handle Position (parallel / right

side) 4. Switch 5. Handle Position (vertical /

upper side)

Operation

► Fig.5: 1. Guide 2. Rebar

► Fig.6: 1. Rebar 2. Guide

1. Screw the Handle into threaded hole at the vertical

or parallel position for easier operation.

2. Ensure that the Switch is at “O” position.

CAUTION: As a safety function of this tool,

the Motor cannot be energised when the battery is

inserted with the Switch at “l” position. For fur-

ther safety, please note that the battery should be

inserted with the Switch at “O” position.

3. Insert the battery into the tool.

4. Slide the Switch to “l” position. The motor is on.

Then push down on the forward end of the Switch to

lock it for operating continuously.

WARNING: Do not touch the rotating parts as

they can cause serious injury.

5. Position the Guide in the opening against the

rebar.

Then push the tool forward slowly to start to cut

the rebar.

CAUTION: When cutting, both at the begin-

ning and near the end, slow down the tool’s for-

ward (cutting) movement. A fast cutting action, at

these times, will damage the Tipped Saw blades

and can cause injury from ying debris.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DSC250 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 7,37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DSC250 Manual

Product: