Manual Makita DSC102 (page 11 of 80) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691563

Zoom out

Zoom in

1/80

11 ENGLISH

Guide scale

Use the guide scale if you wish to cut threaded rods in

the same length. Insert the guide scale into the hole as

shown in the gure.

► Fig.8: 1. Guide scale 2. Clamping screw

Align the value of your desired length on the guide scale

with the cutting line. Then tighten the clamping screw.

► Fig.9: 1. Guide scale 2. Cutting line 3. Clamping

screw

CAUTION: Do not hold the guide scale to

carry or handle the tool. The tool may fall off and

cause personal injury and/or damage to the tool.

Rod guide

For a precise cutting, set the rod guide in position

depending on the diameter of the threaded rod to be

cut.

► Fig.10: 1. Rod guide (Position 1) 2. Rod guide

(Position 2)

There are two rod guide positions.

Position Size of threaded rod

1 W3/8, M10

2 M8, M6

Hook

CAUTION: Never hook the tool on a windy

location or a potentially unstable surface.

CAUTION: Do not use the hook when it is

deformed or damaged.

CAUTION: When not operating the tool,

always fold the hook.

The hook is convenient for hanging the tool temporarily.

► Fig.11: 1. Hook

CAUTION: Do not hang the hook from the

waist belt. It may result in personal injuries and/or

damage to the tool if dropped.

► Fig.12

Hex wrench storage

When not in use, store the hex wrench as shown in the

gure to keep it from being lost.

► Fig.13: 1. Hex wrench

Shoulder strap

Optional accessory

Shoulder strap is useful for carrying the tool.

► Fig.14: 1. Shoulder strap 2. Belt end 3. Buckle

CAUTION: Always wear the shoulder strap

crossed over your body and adjusted in proper

length.

CAUTION: Do not use the shoulder strap if it

is damaged.

CAUTION: Leave an sufcient length between

the buckle and belt end to prevent the belt end

from slipping through the buckle.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing the cutting dice

CAUTION: Always install the cutting dice in

the correct directions and secured rmly. Incorrect

or loose attachment may cause breakage of the

cutting dice, resulting personal injury by own off

fractions.

NOTICE: Remove the burr on the cutting dice

using a le if any.

1. Check if the jaw of the cutting dice is fully opened.

If not, install the battery and pull the switch trigger until

the jaw is fully opened.

CAUTION: Be sure to remove the battery

cartridge if you installed.

2. Set the reversing switch lever to the lock position.

► Fig.15: 1. Reversing switch lever

3. Unscrew the bolts with the supplied hex wrench.

CAUTION: Use only the Makita wrench pro-

vided with the tool. Using other wrenches may

result in overtightening or insufcient tightening which

causes personal injury.

4. Set the cutting dice onto the mounts so that the

two colored markings can be seen.

► Fig.16: 1. Bolt 2. Cutting die 3. Stationary mount

4. Movable mount 5. Colored marking

6. Hex wrench

5. Secure the cutting dice with the bolts rmly.

The cutting dice are correctly installed if the arrows on

them point each other. The dimensions of the cutting

dice are the same but their thickness look different

when seen from above.

► Fig.17: 1. Arrow 2. Cutting die 3. Thin side 4. Thick

side

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DSC102 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 17,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DSC102 Manual

Product: