78880

Makita DP 4003 Manual

5
Zoom out
Zoom in
Previous page
1/8
Next page
5
ENGLISH
Explanation of general view
1Tighten
2 Chuck key
3Sleeve
4 Ring
5 Switch trigger
6 Lock lever
7 Reversing switch lever
8 Side grip
9Protrusions
10 Teeth
11 Loosen
12 Depth gauge
13 Reaction
14 Reverse
15 Forward
16 Holding against a stud.
17 Holding against a floor.
18 Hook
SPECIFICATIONS
Model DP3002 DP3003 DP4000 DP4001 DP4002 DP4003
Capacities
Steel ............................................. 10 mm 10 mm 13 mm 13 mm 13 mm 13 mm
Wood ............................................ 32 mm 32 mm 38 mm 38 mm 38 mm 38 mm
No load speed (min
–1
) ..................... 0 – 1,200 0 – 1,200 0 – 900 0 – 900 0 – 600 0 – 600
Overall length .................................. 304 mm 296 mm 304 mm 308 mm 304 mm 308 mm
Net weight ........................................ 2.0 kg 1.8 kg 2.2 kg 2.0 kg 2.2 kg 2.0 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
SPECIFIC SAFETY RULES
GEB001-2
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to drill safety rules. If you use this power tool
unsafely or incorrectly, you can suffer serious per-
sonal injury.
1. Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
2. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tools
may contact hidden wiring or its own cord.
Contact with a “live” wire will make exposed metal
parts of the tool “live” and shock the opeator.
3. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
4. Hold the tool firmly.
5. Keep hands away from rotating parts.
6. Do not leave the tool running. Operate the tool
only when hand-held.
7. Do not touch the drill bit or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
8. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
OPERATING INSTRUCTIONS
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the side grip, bit
or other accessories.
Installing or removing drill bit
For DP3002, DP4000, DP4002 (Fig. 1)
To install the bit, place it in the chuck as far as it will go.
Tighten the chuck by hand. Place the chuck key in each
of the three holes and tighten clockwise. Be sure to
tighten all three chuck holes evenly. To remove the bit,
turn the chuck key counterclockwise in just one hole,
then loosen the chuck by hand. After using the chuck key,
be sure to return it to the original position.
For DP3003, DP4001, DP4003 (Fig. 2)
Hold the ring and turn the sleeve counterclockwise to
open the chuck jaws. Place the bit in the chuck as far as it
will go. Hold the ring firmly and turn the sleeve clockwise
to tighten the chuck. To remove the bit, hold the ring and
turn the sleeve counterclockwise.
Switch action (Fig.3)
CAUTION:
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the “OFF”
position when released.
To start the tool, simply pull the trigger. Tool speed is
increased by increasing pressure on the trigger. Release
the trigger to stop.
For continuous operation, pull the trigger and then push
the lock lever upward. To stop the tool from the locked
position, pull the trigger fully, then release it.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DP 4003 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DP 4003 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita DP 4003

Makita DP 4003 User Manual - German - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info