Manual Makita DMR108 (page 8 of 104) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Spanish)

690928

Zoom out

Zoom in

1/104

Indicating the remaining battery capacity

(Fig. 8)

Only for battery cartridges with “B” at the end of the

model number

Press the check button on the battery cartridge to indicate

the remaining battery capacity. The indicator lamps light

up for few seconds.

015658

Note:

• Depending on the conditions of use and the ambient

temperature, the indication may differ slightly from the

actual capacity.

Using the soft bended rod antenna (Fig. 9)

Straight up the soft bended rod antenna as shown in the

figure.

Using Supplied AC power adaptor

(Fig. 10)

Remove the rubber protector and insert the adaptor plug

into the DC socket on the left side of the radio. Plug the

adaptor into a standard mains socket outlet. Whenever

the adaptor is used, the battery pack is automatically

disconnected. The AC adaptor should be disconnected

from the main supply when not in use.

Note:

When your radio has any interference in AM band by its

adaptor, please move your radio away from its AC adaptor

over 30 cm.

Operating your radio – Scan tuning AM/

1. Press the Power button to switch on your radio.

2. Press the Source button to select AM or FM radio

mode.

3. Press and hold the Tuning control knob to carry out

an auto-tune. Your radio will scan up the AM/FM band

from the currently displayed frequency and will stop

scanning automatically when it finds a station of

sufficient strength.

4. After a few seconds the display will update. The

display will show the frequency of the signal found.

5. To find other station, press and hold the Tuning control

knob as before.

6. When the end of the waveband is reached your radio

will recommence tuning from the opposite end of the

waveband.

7. Rotate the Tuning control knob to adjust the sound

level as required.

Note:

• While adjusting the volume, make sure the FM/AM is

NOT flashing on the screen.

• If AM/FM is flashing on the screen, it allows you to

tune the stations manually (see the section of

“Manual tuning

– AM/ FM” for more detail).

8. To switch off your radio press the Power button .

Manual tuning – AM/FM

1. Press the Power button to switch on your radio.

2. Press the Source button to select AM or FM radio

mode.

3. Press the Tuning control knob and you will see the

FM or AM is flashing on the display.

Note:

• FM/AM will flash approx. 10 seconds. Within this

period, only manual tuning is allowed.

• If volume adjustment is desired while FM/AM is

flashing, press the Tuning control knob to stop the

flash and you can rotate the Tuning control knob to

adjust sound level.

4. Rotate the Tuning control knob to tune to a station.

5. When the end of the waveband is reached your radio

will recommence tuning from the opposite end of the

waveband.

6. Use the Tuning control knob to adjust the sound

level as required.

Presetting stations in AM/FM mode

There are 5 preset stations each for AM and FM radio.

They are used in the same way for each waveband.

1. Press the Power button to switch on your radio.

2. Press the Source button to select the desired

waveband. Tune to the required radio station as

previously described.

3. Press and hold the required Preset button (1 to 5)

until the display shows “P4” for

example after the frequency. The station will be stored

using the preset number. Repeat this procedure for

the remaining presets as you wish.

Indicator lamps

Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery may

have

malfunctioned.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DMR108 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 59,24 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DMR108 Manual

Product: