691731
10
Zoom out
Zoom in
Previous page
1/21
Next page
10 ENGLISH
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
►Fig.5: 1. Indicator lamps 2.Checkbutton
Pressthecheckbuttononthebatterycartridgetoindi-
catetheremainingbatterycapacity.Theindicatorlamps
light up for a few seconds.
Indicator lamps Remaining
capacity
Lighted Off Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
Thebattery
may have
malfunctioned.
NOTE: Depending on the conditions of use and the
ambienttemperature,theindicationmaydifferslightly
from the actual capacity.
Switch action
WARNING: Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
►Fig.6: 1.Lock-offbutton2. Switch trigger
Topreventtheswitchtriggerfrombeingaccidentally
pulled,alock-offbuttonisprovided.Tostartthetool,
pressthelock-offbuttonandpulltheswitchtrigger.
Release the switch trigger to stop.
WARNING: NEVER defeat the lock-off button
by taping down or some other means.Aswitchwith
anegatedlock-offbuttonmayresultinunintentional
operationandseriouspersonalinjury.
WARNING: NEVER use the tool if it runs when
you simply pull the switch trigger without press-
ing the lock-off button.Aswitchinneedofrepair
may result in unintentional operation and serious
personalinjury.ReturntooltoaMakitaservicecenter
forproperrepairsBEFOREfurtherusage.
NOTICE: Do not pull the switch trigger hard
without pressing in the lock-off button. This can
causeswitchbreakage.
Load status indicator
The load status indicator shows the level of the load on
themotorduringcuttingoperation.Astheloadonthe
motorincreases,thenumberoflightinglampincreases.
►Fig.7: 1. Load status indicator
Overload alert
If the motor is operated with excessive load, all lamps of
theloadstatusindicatorwillblink.Inthiscase,reducethe
load on the motor. If you continue to load the motor while
theloadstatusindicatorisblinking,thetoolwillautomati
-
cally stops in few seconds due to overload protection.
NOTE
: If an excessive load is generated at once, the tool
automaticallystopswithoutblinkingoftheloadstatusindicator.
Interval between vise and guide plate
CAUTION: After adjusting the interval
between the vise and the guide plate, make
sure that the guide plate is properly secured.
Insufcientxingmayresultinpersonalinjury.
Thefollowingintervalsettingsoftheviseareavailable:
0 - 170 mm (original setting)
35 - 205 mm
70 - 240 mm
Ifyourworkrequiresdifferentsetting,proceedasfol-
lows to change the spacing or interval.
Loosen the screw on the guide plate. Move the guide
plate to the desired position then tighten the screw.
►Fig.8: 1. Screw 2. Guide plate
Cutting angle adjustment
CAUTION: After adjusting the angle of the
guide plate, make sure that the guide plate is
properly secured.Insufcientxingmayresultin
personalinjury.
CAUTION: Do not operate the tool when
the material is not rmly secured with the vise
because of the cutting angle.
Turn the lever counterclockwise. Move the guide plate
to the desired angle and fully tighten the lever.
►Fig.9: 1. Guide plate 2. Lever
NOTE: The scale on the guide plate is only a rough
indication.Formoreaccurateangle,useaprotractor
or triangle ruler. Keep the handle down so that the
cut-offwheelextendsintothebase.Atthesametime,
adjusttheanglebetweentheguideplateandthecut-
off wheel with a protractor or triangle ruler.
Spark guard adjustment
Country specic
The spark guard is factory-installed with its lower edge contact-
ingthebase.Operatingthetoolinthispositionwillcausemany
sparkstoyaround.Loosenthescrewandadjustthespark
guardtoapositionatwhichminimumsparkswillyaround.
►Fig.10: 1. Screw 2. Spark guard
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DLW140 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DLW140 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 5,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info