691786

Makita DLS600 Manual

23
Zoom out
Zoom in
Previous page
1/160
Next page
23 ENGLISH
MAINTENANCE
WARNING: Always be sure that the blade is
sharp and clean for the best and safest perfor-
mance. Attempting a cut with a dull and /or dirty blade
may cause kickback and result in a serious personal
injury.
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE: Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs,anyothermaintenanceoradjustmentshould
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Adjusting the cutting angle
Thistooliscarefullyadjustedandalignedatthefactory,
but rough handling may have affected the alignment. If
your tool is not aligned properly, perform the following:
Miter angle
1. Loosenthexingscrewcounterclockwise.
2. Rotate the turn base until the pointer indicates 0°
on the miter scale.
►Fig.52: 1. Fixing screw 2. Turn base 3. Miter scale
4. Pointer
3. Rotate the turn base slightly clockwise and coun-
terclockwise to seat the turn base in the 0° miter notch.
(Leave as it is if the pointer does not indicate 0°.)
4. Loosen the hex socket bolt securing the guide
fence using the hex wrench.
►Fig.53: 1. Guide fence 2. Hex socket bolt
►Fig.54: 1. Guide fence 2. Hex socket bolt
5. Lower the handle fully and lock it in the lowered
position by pushing in the stopper pin.
6. Adjusttheguidefenceuntilitmakesaperpendic-
ular angle with the blade using a triangular rule, try-
square, etc. Then securely tighten the hex socket bolt
on the guide fence.
►Fig.55: 1. Guide fence 2. Triangular rule 3. Saw
blade
7. Make sure that the pointer indicates 0° on the
miter scale. If the pointer does not indicate 0°, loosen
thescrewwhichsecuresthepointerandadjustthe
pointer so that it indicates 0°.
►Fig.56: 1. Screw 2. Miter scale 3. Pointer
Bevel angle
0° bevel angle
1. Lower the handle fully and lock it in the lowered
position by pushing in the stopper pin.
2. Loosen the lever at the rear of the tool.
3. Turnthe0°bevelangleadjustingboltontheright
side of the saw head two or three revolutions counter-
clockwise to tilt the blade to the right.
►Fig.57: 1.Adjustingbolt2. Lever
4. Turnthe0°bevelangleadjustingboltclockwise
carefully until the side of the blade makes a perpendic-
ular angle with the top surface of the turn base. Use the
triangular rule, try-square, etc. as a guide. Then tighten
the lever securely.
►Fig.58: 1. Triangular rule 2. Saw blade 3. Top sur-
face of turn table
5. Make sure that the pointer on the arm indicates 0°
on the bevel scale. If it does not indicate 0°, loosen the
screwwhichsecuresthepointerandadjustthepointer
so that it indicates 0°.
►Fig.59: 1. Screw 2. Pointer 3. Bevel scale
45° bevel angle
Adjustthe45°bevelangleonlyafterperforming0°
bevelangleadjustment.
1. Loosen the lever and tilt the blade to the left fully.
2. Make sure that the pointer on the arm indicates
45° on the bevel scale. If the pointer does not indicate
45°,turntheleft45°bevelangleadjustingboltonthe
right side of the arm until the pointer indicates 45°.
►Fig.60: 1.Right45°bevelangleadjustingbolt
2. Pointer 3.Left45°bevelangleadjusting
bolt
3. Tiltthebladetotherightfully,andthenadjustthe
right 45° bevel angle using the right 45° bevel angle
adjustingbolt.
►Fig.61: 1. Saw blade 2. Triangular rule
Adjusting the laser line position
WARNING: The battery cartridge must be
installed on the tool while adjusting the laser line.
Take extra care not to switch on the tool during
adjustment. Accidental start up of the tool may result
inseriouspersonalinjury.
CAUTION: Never look directly into the laser
beam. Direct eye exposure to the beam could cause
serious damage to your eyes.
NOTICE: Check the position of laser line regu-
larly for accuracy.
NOTICE: Beware that impacts to the tool. It may
cause the laser line to be misaligned or may cause
damage to the laser, shortening its life.
NOTICE: Have the tool repaired by a Makita
authorized service center for any failure on the
laser unit.
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DLS600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DLS600 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 32,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info