Manual Makita DLM461 (page 11 of 27) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

690895

Zoom out

Zoom in

1/27

11 ENGLISH

59. After removing the battery from the machine or

charger, be sure to attach the battery cover to

the battery and store it in a dry place.

60. Do not replace the battery with wet hands.

61. Do not use the machine in the snow.

62. If the cut-off grass is wet, it is likely to be

clogged inside of the machine. Check the con-

dition of the machine regularly, and remove the

adhered grass as necessary.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity

with product (gained from repeated use) replace strict

adherence to safety rules for the subject product.

MISUSE or failure to follow the safety rules stated in this

instruction manual may cause serious personal injury.

Important safety instructions for

battery cartridge

Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery char-

ger, (2) battery, and (3) product using battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require-

ments.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.

Tape or mask off open contacts and pack up the

battery in such a manner that it cannot move

around in the packaging.

11. Follow your local regulations relating to dis-

posal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliant products may result in a re, exces-

sive heat, explosion, or leak of electrolyte.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causing res, personal injury and damage. It will

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery

service life.

Charge the battery cartridge with room tempera-

ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot

battery cartridge cool down before charging it.

4. Charge the battery cartridge if you do not use

it for a long period (more than six months).

ASSEMBLY

WARNING: Always be sure that the lock key

and battery cartridge are removed before carrying

out any work on the mower. Failure to remove the

lock key and the battery cartridge may result in seri-

ous personal injury from accidental start-up.

WARNING: Never start the mower unless it is

completely assembled. Operation of the tools in a

partially assembled state may result in serious per-

sonal injury from accidental start-up.

Installing the handle

NOTICE: When installing handles, position the

cords so that they are not caught by anything

between the handles. If the cord is damaged, the

mower switch may not work.

1. Attach the lower handle so that the holes in the

handle t in the protrusions on the mower body. Insert

the bolts from inside, then attach washer A from outside,

and then tighten the thumb nuts.

► Fig.1: 1. Lower handle 2. Washer A 3. Thumb nut

4. Protrusion 5. Hole 6. Bolt

2. Align the hole in the lower handle with the hole

in the upper handle, then insert the bolts from inside,

then attach washer B from outside, and then tighten the

thumb nuts.

► Fig.2: 1. Upper handle 2. Hole 3. Washer B

4. Thumb nut 5. Lower handle 6. Bolt

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DLM461 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 5,95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DLM461 Manual

Product: