711185

Makita DJR187RTE Manual

7
Zoom out
Zoom in
Previous page
1/60
Next page
7 ENGLISH
• For high speed
Whenthelock/speedchangeleverisdepressed
fromAside,thestrokespeedisat“2”.
• For low speed
Whenthelock/speedchangeleverisdepressed
from B side, the stroke speed is at “1”.
Whenthelock/speedchangeleverisin
position, the
toolislockedandtheswitchtriggercannnotbepulled.
Lighting up the front lamp
►Fig.6: 1. Lamp
CAUTION: Do not look in the light or see the
source of light directly.
Pulltheswitchtriggertolightupthelamp.Thelamp
keepsonlightingwhiletheswitchtriggerisbeingpulled.
Thelampgoesoutapproximately10secondsafter
releasing the switch trigger.
NOTE: Use a dry cloth to wipe the dirt off the lens of
the lamp. Be careful not to scratch the lens of lamp, or
it may lower the illumination.
NOTE:Whenthetoolisoverheated,thelampblinks
foroneminute.Inthiscase,cooldownthetoolbefore
another operation.
Adjusting the shoe
Whenthereciprosawbladelosesitscuttingefciency
in one place along its cutting edge, reposition the shoe
to utilize a sharp, unused portion of its cutting edge.
Thiswillhelptolengthenthelifeofthereciprosaw
blade.
Thepositionoftheshoecanbeadjustedinvelevels.
Torepositiontheshoe,opentheshoeadjustinglever
andselectthesuitableposition,thenclosetheshoe
adjustinglever.
►Fig.7: 1. Shoe 2.Shoeadjustinglever
NOTE:Theshoecannotbeadjustedwithoutopening
theshoeadjustingleverfully.
Hook
CAUTION: When hanging the tool, set the
lock/speed change lever in position to lock
the switch trigger. (See the section titled “Switch
action” .)
CAUTION: Never hang the tool at high or
potentially unstable location.
►Fig.8: 1. Hook
Thehookisconvenientforhangingthetooltemporarily.
Tousethehook,simplyliftuphookuntilitsnapsinto
the open position.
When not in use, always lower hook until it snaps into
the closed position.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing the recipro
saw blade
CAUTION: Always clean out all chips or for-
eign matter adhering to the blade and around the
blade clamp.Failuretodosomaycauseinsufcient
tighteningoftheblade,resultinginaseriousinjury.
Toinstallthereciprosawblade,alwaysmakesurethat
thebladeclamplever(partofthebladeclampsleeve)
is in released position ontheinsulationcoverbefore
insertingthereciprosawblade.Ifthebladeclamplever
isinxedposition,rotatethebladeclampleverinthe
directionofthearrowsothatitcanbelockedatthe
released positon
.
►Fig.9: 1. Blade clamp lever 2. Released position
3. Fixed position
Insertthereciprosawbladeintothebladeclampasfar
asitwillgo.Thebladeclampsleeverotatesandxes
thereciprosawblade.Makesurethatthereciprosaw
bladecannotbeextractedeventhoughyoutrytopull
it out.
►Fig.10: 1.Reciprosawblade2. Blade clamp sleeve
CAUTION: If you do not insert the recipro saw
blade deep enough, the recipro saw blade may be
ejected unexpectedly during operation.Thiscan
beextremelydangerous.
Toremovethereciprosawblade,rotatetheblade
clampleverinthedirectionofthearrowfully.Thereci-
prosawbladeisremovedandthebladeclampleveris
xedatthereleasedposition .
►Fig.11: 1.Reciprosawblade2. Blade clamp lever
CAUTION: Keep hands and ngers away from
the lever during the switching operation. Failure
to do so may cause personal injuries.
NOTE:Ifyouremovethereciprosawbladewithout
rotatingthebladeclampleverfully,thelevermaynot
belockedinthereleasedposition .Inthiscase,
rotatethebladeclampleverfullyagain,thenmake
surethatthebladeclampleverlockedatthereleased
position .
NOTE:Ifthebladeclampleverispositionedinside
thetool,switchonthetooljustasecondtoletthe
bladeoutasshowninthegure.Removethebattery
cartridgefromthetoolbeforeinstallingorremoving
thereciprosawblade.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DJR187RTE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DJR187RTE in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 13,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info