711187

Makita DJR186ZK Manual

7
Zoom out
Zoom in
Previous page
1/56
Next page
7 ENGLISH
Topreventtheswitchtriggerfromaccidentallypulled,
thelock-offbuttonisprovided.
Tostartthetool,depressthelock-offbuttonfromBside
and pull the switch trigger.
Toolspeedisincreasedbyincreasingpressureonthe
switchtrigger.Releasetheswitchtriggertostop.After
use,alwayspressinthelock-offbuttonfromAside.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing the recipro
saw blade
CAUTION: Always clean out all chips or for-
eign matter adhering to the blade and around the
blade clamp.Failuretodosomaycauseinsufcient
tighteningoftheblade,resultinginaseriousinjury.
Toinstallthereciprosawblade,alwaysmakesurethat
thebladeclamplever(partofthebladeclampsleeve)
is in released position
ontheinsulationcoverbefore
insertingthereciprosawblade.Ifthebladeclamplever
isinxedposition,rotatethebladeclampleverinthe
directionofthearrowsothatitcanbelockedatthe
released positon .
►Fig.5: 1. Blade clamp lever 2. Released position
3. Fixed position
Insertthereciprosawbladeintothebladeclampasfar
asitwillgo.Thebladeclampsleeverotatesandxes
thereciprosawblade.Makesurethatthereciprosaw
bladecannotbeextractedeventhoughyoutrytopull
it out.
►Fig.6: 1.Reciprosawblade2. Blade clamp sleeve
CAUTION: If you do not insert the recipro saw
blade deep enough, the recipro saw blade may be
ejected unexpectedly during operation.Thiscan
beextremelydangerous.
Toremovethereciprosawblade,rotatetheblade
clampleverinthedirectionofthearrowfully.Thereci-
prosawbladeisremovedandthebladeclampleveris
xedatthereleasedposition
.
►Fig.7: 1.Reciprosawblade2. Blade clamp lever
CAUTION: Keep hands and ngers away from
the lever during the switching operation. Failure
to do so may cause personal injuries.
NOTE:Ifyouremovethereciprosawbladewithout
rotatingthebladeclampleverfully,thelevermaynot
belockedinthereleasedposition .Inthiscase,
rotatethebladeclampleverfullyagain,thenmake
surethatthebladeclampleverlockedatthereleased
position
.
NOTE:Ifthebladeclampleverispositionedinside
thetool,switchonthetooljustasecondtoletthe
bladeoutasshowninthegure.Removethebattery
cartridgefromthetoolbeforeinstallingorremoving
thereciprosawblade.
OPERATION
CAUTION: Always press the shoe rmly
against the workpiece during operation.Ifthe
shoe is removed or held away from the workpiece
duringoperation,strongvibrationand/ortwistingwill
beproduced,causingthebladetosnapdangerously.
CAUTION: Always wear gloves to protect
your hands from hot ying chips when cutting
metal.
CAUTION: Be sure to always wear suitable
eye protection which conforms with current
national standards.
CAUTION: Always use a suitable coolant
(cutting oil) when cutting metal. Failure to do so will
causeprematurebladewear.
Presstheshoermlyagainsttheworkpiece.Donot
allowthetooltobounce.Bringthereciprosawblade
into light contact with the workpiece. First, make a pilot
grooveusingaslowerspeed.Thenuseafasterspeed
to continue cutting.
►Fig.8
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DJR186ZK at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DJR186ZK in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 11,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info