Manual Makita DHS680 (page 9 of 84) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

600423

Zoom out

Zoom in

1/84

properly and returns to the “OFF” position when

released.

• Do not pull the switch trigger hard without pressing the

lock-off lever. This can cause switch breakage. (Fig. 9)

To prevent the switch trigger from being accidentally

pulled, a lock-off lever is provided. To start the tool, press

the lock-off lever and pull the switch trigger. Release the

switch trigger to stop.

WARNING:

• For your safety, this tool is equipped with lock-off lever

which prevents the tool from unintended starting.

NEVER use the tool if it runs when you simply pull the

switch trigger without pressing the lock-off lever. Return

tool to a MAKITA service center for proper repairs

BEFORE further usage.

• NEVER tape down or defeat purpose and function of

lock-off lever.

Indicating remaining battery capacity

(Fig. 10)

When you turn the tool on, the battery indicator shows the

remaining battery capacity.

The remaining battery capacity is shown as the following

table.

015146

Automatic speed change function

(Fig. 11)

015137

This tool has “high speed mode” and “high torque mode”.

It automatically changes operation mode depending on

the work load. When mode indicator lights up during

operation, the tool is in high torque mode.

Tool/battery protection system

The tool is equipped with a tool/battery protection system.

This system automatically cuts off power to the motor to

extend tool and battery life.

The tool will automatically stop during operation if the tool

or battery are placed under one of the following

conditions. In some conditions, the indicator lights up.

Overload protection

When the tool is operated in a manner that causes it to

draw an abnormally high current, the tool automatically

stops without any indications. In this situation, turn the tool

off and stop the application that caused the tool to

become overloaded. Then turn the tool on to restart.

Overheat protection for tool

When the tool is overheated, the tool stops automatically

and the battery indicator shows following state. In this

situation, let the tool cool before turning the tool on again.

015145

Releasing protection lock

When the protection system works repeatedly, the tool is

locked and the battery indicator shows the following state.

015201

In this situation, the tool does not start even if turning the

tool off and on. To release the protection lock, remove the

battery, set it to the battery charger and wait until the

charging finishes.

Adjusting depth of cut

CAUTION:

• After adjusting the depth of cut, always tighten the lever

securely.

Loosen the lever on the side of the rear handle and move

the base up or down. At the desired depth of cut, secure

the base by tightening the lever. (Fig. 12)

For cleaner, safer cuts, set cut depth so that no more than

one blade tooth projects below workpiece. Using proper

cut depth helps to reduce potential for dangerous

KICKBACKS which can cause personal injury.

Bevel cutting

Loosen the front lever. Set for the desired angle (0° - 50°)

by tilting accordingly, then tighten the front lever securely.

(Fig. 13)

Use the 45° stopper when you do precise 45° angle

cutting. Turn the stopper counterclockwise fully for bevel

cut (0° - 45°) and turn it clockwise for 0° - 50° bevel cuts.

(Fig. 14)

Battery indicator status

Remaining battery

capacity

: On : Off : Blinking

50% - 100%

20% - 50%

0% - 20%

Charge the battery

Mode indicator status Operation mode

High speed mode

High torque mode

Battery indicator : On : Off : Blinking

Tool is overheated

Battery indicator : On : Off : Blinking

Protection lock works

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DHS680 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 10,17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DHS680 Manual

Product: