Manual Makita DHS660 (page 16 of 148) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691827

Zoom out

Zoom in

1/148

16 ENGLISH

For tool with the inner ange for a

15.88 mm hole-diameter saw blade

(country specic)

Mounttheinnerangewithitsrecessedsidefacing

outward onto the mounting shaft and then place circu-

larsawblade(withtheringattachedifneeded),outer

angeandhexbolt.

For tool without the ring

►Fig.26: 1. Mounting shaft 2.Innerange3. Circular

saw blade 4.Outerange5. Hex bolt

For tool with the ring

►Fig.27: 1. Mounting shaft 2.Innerange3. Circular

saw blade 4.Outerange5. Hex bolt

6. Ring

WARNING: BE SURE TO TIGHTEN THE HEX

BOLT CLOCKWISE SECURELY. Also be careful

not to tighten the bolt forcibly. Slipping your hand

from the hex wrench can cause a personal injury.

WARNING: If the ring is needed to mount the

blade onto the spindle, always be sure that the

correct ring for the blade's arbor hole you intend

to use is installed between the inner and the outer

anges.Useoftheincorrectarborholeringmay

result in the improper mounting of the blade causing

blade movement and severe vibration resulting in

possible loss of control during operation and in seri-

ouspersonalinjury.

Blade guard cleaning

When changing the circular saw blade, make sure to

also clean the upper and lower blade guards of accu-

mulated sawdust as discussed in the Maintenance

section. Such efforts do not replace the need to check

lower guard operation before each use.

Connecting a vacuum cleaner

Whenyouwishtoperformcleancuttingoperation,

connectaMakitavacuumcleanertoyourtool.Connect

ahoseofthevacuumcleanertothedustnozzleas

showninthegure.

►Fig.28: 1.Dustnozzle2. Screw

►Fig.29: 1. Hose 2. Vacuum cleaner

OPERATION

CAUTION: Be sure to move the tool forward

in a straight line gently. Forcing or twisting the tool

will result in overheating the motor and dangerous

kickback,possiblycausingsevereinjury.

NOTE:Whenthebatterycartridgetemperatureis

low,thetoolmaynotworktoitsfullcapacity.Atthis

time,forexample,usethetoolforalight-dutycutfor

awhileuntilthebatterycartridgewarmsupashigh

as room temperature. Then, the tool can work to its

fullcapacity.

►Fig.30

Holdthetoolrmly.Thetoolisprovidedwithbothafrontgrip

and rear handle. Use both to best grasp the tool. If both hands

areholdingsaw,theycannotbecutbythecircularsawblade.

Set the base on the workpiece to be cut without the circular

sawblademakinganycontact.Thenturnthetoolonandwait

untilthecircularsawbladeattainsfullspeed.Nowsimply

move the tool forward over the workpiece surface, keeping it

atandadvancingsmoothlyuntilthesawingiscompleted.

Togetcleancuts,keepyoursawinglinestraightandyour

speedofadvanceuniform.Ifthecutfailstoproperlyfollowyour

intended cut line, do not attempt to turn or force the tool back

tothecutline.Doingsomaybindthecircularsawbladeand

leadtodangerouskickbackandpossibleseriousinjury.Release

switch, wait for circular saw blade to stop and then withdraw tool.

Realign tool on new cut line, and start cut again. Attempt to avoid

positioning which exposes operator to chips and wood dust being

ejectedfromsaw.Useeyeprotectiontohelpavoidinjury.

Rip fence (Guide rule)

Optional accessory

►Fig.31: 1.Ripfence(Guiderule)2. Clamping screw

Thehandyripfenceallowsyoutodoextra-accurate

straightcuts.Simplyslidetheripfenceupsnugly

against the side of the workpiece and secure it in posi-

tion with the clamping screw on the front of the base. It

also makes repeated cuts of uniform width possible.

Lanyard (tether strap) connection

Safety warnings specic for use at height

Read all safety warnings and instructions. Failure to follow

thewarningsandinstructionsmayresultinseriousinjury.

Always keep the tool tethered when working "at

height". Maximum lanyard length is 2 m (6.5 ft).

2. Use only with lanyards appropriate for this tool

type and rated for at least 4.0 kg (8.8 lbs).

3. Do not anchor the tool lanyard to anything on

your body or on movable components. Anchor

the tool lanyard to a rigid structure that can

withstand the forces of a dropped tool.

4. Make sure the lanyard is properly secured at

each end prior to use.

5. Inspect the tool and lanyard before each use

for damage and proper function (including

fabric and stitching). Do not use if damaged or

not functioning properly.

6. Do not wrap lanyards around or allow them to

come in contact with sharp or rough edges.

7. Fasten the other end of the lanyard outside

the working area so that a falling tool is held

securely.

8. Attach the lanyard so that the tool will move

away from the operator if it falls. Dropped tools

willswingonthelanyard,whichcouldcauseinjury

or loss of balance.

9. Do not use near moving parts or running

machinery.Failuretodosomayresultinacrush

orentanglementhazard.

10. Do not carry the tool by the attachment device

or the lanyard.

11. Only transfer the tool between your hands

while you are properly balanced.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DHS660 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 27,56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DHS660 Manual

Product: