Manual Makita DHS660 (page 13 of 148) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691827

Zoom out

Zoom in

1/148

13 ENGLISH

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery cartridge

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge.Failuretoholdthetoolandthebattery

cartridgermlymaycausethemtoslipoffyourhands

andresultindamagetothetoolandbatterycartridge

andapersonalinjury.

►Fig.7: 1. Red indicator 2. Button 3.Batterycartridge

Toremovethebatterycartridge,slideitfromthetool

while sliding the button on the front of the cartridge.

Toinstallthebatterycartridge,alignthetongueonthe

batterycartridgewiththegrooveinthehousingandslip

itintoplace.Insertitallthewayuntilitlocksinplace

withalittleclick.Ifyoucanseetheredindicatoronthe

uppersideofthebutton,itisnotlockedcompletely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

itmayaccidentallyfalloutofthetool,causinginjuryto

youorsomeonearoundyou.

CAUTION: Do not install the battery cartridge

forcibly.Ifthecartridgedoesnotslideineasily,itis

notbeinginsertedcorrectly.

Tool / battery protection system

Thetoolisequippedwithatool/batteryprotectionsys-

tem.Thissystemautomaticallycutsoffpowertothe

motortoextendtoolandbatterylife.Thetoolwillauto-

maticallystopduringoperationifthetoolorbatteryis

placed under one of the following conditions.

Overload protection

Whenthetool/batteryisoperatedinamannerthat

causesittodrawanabnormallyhighcurrent,thetool

automaticallystops.Inthissituation,turnthetooloff

and stop the application that caused the tool to become

overloaded. Then turn the tool on to restart.

Overheat protection

Whenthetool/batteryisoverheated,thetoolstops

automatically,andthebatteryindicatorblinkabout60

seconds. In this situation, let the tool cool down before

turning the tool on again.

On Blinking

Overdischarge protection

Whenthebatterycapacitybecomeslow,thetoolstops

automatically.Iftheproductdoesnotoperateeven

when the switches are operated, remove the batteries

from the tool and charge the batteries.

Releasing protection lock

Whentheprotectionsystemworksrepeatedly,thetool

islockedandthebatteryindicatorshowsthefollowing

state.

Blinking Off

In this situation, the tool does not start even if turning

the tool off and on. To release the protection lock,

removethebattery,setittothebatterychargerandwait

untilthechargingnishes.

Indicating the remaining battery

capacity

Whenyoupulltheswitchtrigger,thebatteryindicator

showstheremainingbatterycapacity.

►Fig.8: 1.Batteryindicator

Theremainingbatterycapacityisshownasthefollow-

ing table.

Battery indicator status Remaining

battery

capacity

Off

Blinking

50% to 100%

20% to 50%

0% to 20%

Charge the

battery

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DHS660 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 27,56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DHS660 Manual

Product: