Manual Makita DHR182 (page 19 of 152) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691040

Zoom out

Zoom in

1/152

19 ENGLISH

3. Disposeofthedust,andthencleanthelter.

►Fig.39

NOTICE: When cleaning the lter, do not touch

the lter with brush or similar, or blow com-

pressed air on the lter. It may damage the lter.

Blow-out bulb

Optional accessory

Afterdrillingthehole,usetheblow-outbulbtocleanthe

dust out of the hole.

►Fig.40

Using dust cup set

Optional accessory

Fit the dust cup set against the ceiling when operating

the tool.

►Fig.41

NOTICE: Do not use the dust cup set when drill-

ing in metal or similar. It may damage the dust

cup set due to the heat produced by small metal

dust or similar.

NOTICE: Do not install or remove the dust cup

set with the drill bit installed in the tool. It may

damage the dust cup set and cause dust leak.

Connecting lanyard (tether strap) to

tool hanger

Safety

warnings specic for use at height

Read all safety warnings and instructions. Failure to follow

thewarningsandinstructionsmayresultinseriousinjury.

1. Always keep the tool tethered when working

"at height". Maximum lanyard length is 2 m.

2. Use only with lanyards appropriate for this tool

type and rated for at least 4.5 kg.

3. Do not anchor the tool lanyard to anything on

your body or on movable components. Anchor

the tool lanyard to a rigid structure that can

withstand the forces of a dropped tool.

4. Make sure the lanyard is properly secured at

each end prior to use.

5. Inspect the tool and lanyard before each use

for damage and proper function (including

fabric and stitching). Do not use if damaged or

not functioning properly.

6. Do not wrap lanyards around or allow them to

come in contact with sharp or rough edges.

Fasten the other end of the lanyard outside the

working area so that a falling tool is held securely.

8. Attach the lanyard so that the tool will move

away from the operator if it falls. Dropped tools

willswingonthelanyard,whichcouldcauseinjury

or loss of balance.

9. Do not use near moving parts or running

machinery. Failure to do so may result in a crush

or entanglement hazard.

10. Do not carry the tool by the attachment device

or the lanyard.

11. Only transfer the tool between your hands

while you are properly balanced.

12. Do not attach lanyards to the tool in a way that

keeps switches or trigger-lock (if supplied)

from operating properly.

13. Avoid getting tangled in the lanyard.

14.

Keep lanyard away from the drilling area of the tool.

15.

Use multi-action and screw gate type carabineers.

Do not use single action spring clip carabineers.

16.

In the event the tool is dropped, it must be tagged

and removed from service, and should be inspected

by a Makita Factory or Authorized Service Center.

►Fig.42: 1.Toolhanger2. Lanyard (tether strap)

WIRELESS ACTIVATION

FUNCTION

Optional accessory

What you can do with the wireless

activation function

Thewirelessactivationfunctionenablescleanandcom-

fortable operation. By connecting a supported vacuum

cleaner to the tool, you can run the vacuum cleaner

automatically along with the switch operation of the tool.

►Fig.43

Tousethewirelessactivationfunction,preparefollow-

ing items:

• Awirelessunit(optionalaccessory)

• Avacuumcleanerwhichsupportsthewireless

activation function

Theoverviewofthewirelessactivationfunctionsettingisas

follows. Refer to each section for detail procedures.

1. Installing the wireless unit

2. Toolregistrationforthevacuumcleaner

3. Starting the wireless activation function

Installing the wireless unit

Optional accessory

CAUTION: Place the tool on a at and stable

surface when installing the wireless unit.

NOTICE:

Clean the dust and dirt on the tool before

installing the wireless unit. Dust or dirt may cause mal-

function if it comes into the slot of the wireless unit.

NOTICE:

To prevent the malfunction caused by static,

touch a static discharging material, such as a metal part of

the tool, before picking up the wireless unit.

NOTICE:

When installing the wireless unit, always

be sure that the wireless unit is inserted in the correct

direction and the lid is completely closed.

1. Openthelidonthetoolasshowninthegure.

►Fig.44: 1. Lid

2. Insert the wireless unit to the slot and then close

the lid.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DHR182 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 26,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DHR182 Manual

Product: