Manual Makita DHP482RTJ (page 10 of 72) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

711039

Zoom out

Zoom in

1/72

10 ENGLISH

Drilling in metal

Topreventthedrillbitfromslippingwhenstartinga

hole, make an indentation with a center-punch and

hammeratthepointtobedrilled.Placethepointofthe

drillbitintheindentationandstartdrilling.

Useacuttinglubricantwhendrillingmetals.Theexcep-

tionsareironandbrasswhichshouldbedrilleddry.

CAUTION: Pressing excessively on the tool

will not speed up the drilling. In fact, this excessive

pressure will only serve to damage the tip of your drill

bit,decreasethetoolperformanceandshortenthe

service life of the tool.

CAUTION: Hold the tool rmly and exert care

when the drill bit begins to break through the

workpiece.Thereisatremendousforceexertedon

thetool/drillbitatthetimeofholebreakthrough.

CAUTION: A stuck drill bit can be removed

simply by setting the reversing switch to reverse

rotation in order to back out. However, the tool

may back out abruptly if you do not hold it rmly.

CAUTION: Always secure small workpieces

in a vise or similar hold-down device.

CAUTION: If the tool is operated continuously

until the battery cartridge has discharged, allow

the tool to rest for 15 minutes before proceeding

with a fresh battery.

MAINTENANCE

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before attempting to perform inspection or

maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

Replacing carbon brushes

►Fig.15: 1. Limit mark

Checkthecarbonbrushesregularly.

Replace them when they wear down to the limit mark.

Keepthecarbonbrushescleanandfreetoslipinthe

holders.Bothcarbonbrushesshouldbereplacedatthe

sametime.Useonlyidenticalcarbonbrushes.

1. Use a screwdriver to remove two screws then

remove the rear cover.

►Fig.16: 1. Rear cover 2. Screw

2. Raise the arm part of the spring and then place

itintherecessedpartofthehousingwithaslottedbit

screwdriver of slender shaft or the like.

►Fig.17: 1. Recessed part 2. Spring 3.Arm

3. Useplierstoremovethecarbonbrushcapsof

thecarbonbrushes.Takeouttheworncarbonbrushes,

insertthenewonesandreplacethecarbonbrushcaps

in reverse.

►Fig.18: 1.Carbonbrushcap

4. Make sure to place the lead wire in opposite side

of the arm.

►Fig.19: 1. Lead wire 2.Carbonbrushcap

5. Makesurethatthecarbonbrushcapshavetinto

theholesinbrushholderssecurely.

►Fig.20: 1. Hole 2.Carbonbrushcap

6. Reinstall the rear cover and tighten two screws

securely.

7. Insertthebatterycartridgeintothetoolandbreak

inbrushesbyrunningtoolwithnoloadforabout1

minute.

8. Checkthetoolwhilerunningandelectricbrake

operation when releasing the switch trigger. If electric

brakeisnotworkingwell,askMakitaAuthorizedor

Factory Service Centers for repair.

TomaintainproductSAFETYandRELIABILITY,

repairs,anyothermaintenanceoradjustmentshould

beperformedbyMakitaAuthorizedorFactoryService

Centers, always using Makita replacement parts.

OPTIONAL

ACCESSORIES

CAUTION: These accessories or attachments

are recommended for use with your Makita tool

specied in this manual.Theuseofanyother

accessories or attachments might present a risk of

injurytopersons.Onlyuseaccessoryorattachment

for its stated purpose.

If you need any assistance for more details regard-

ing these accessories, ask your local Makita Service

Center.

• Drillbits

• Driverbits

• Tungsten-carbidetippeddrillbit

• Blow-outbulb

• Driverbitholder

• Hook

• Makitagenuinebatteryandcharger

NOTE:Someitemsinthelistmaybeincludedinthe

toolpackageasstandardaccessories.Theymay

differ from country to country.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DHP482RTJ in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 16,99 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DHP482RTJ Manual

Product: