600447
7
Zoom out
Zoom in
Previous page
1/14
Next page
7
ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and the bat-
tery cartridge is removed before carrying out any work
on the tool.
Installing or removing wheel point (Fig. 5 & 6)
Loosen the collet nut and insert the wheel point into the
collet nut. Use one wrench to hold the spindle and the
other one to tighten the collet nut securely.
The wheel point should not be mounted more than 8 mm
from the collet nut. Exceeding this distance could cause
vibration or a broken shaft.
To remove the wheel point, follow the installation proce-
dure in reverse.
CAUTION:
Use the correct size collet cone for the wheel point
which you intend to use.
OPERATION (Fig. 7)
Turn the tool on without the wheel point making any con-
tact with the workpiece and wait until the wheel point
attains full speed. Then apply the wheel point to the
workpiece gently. To obtain a good finish, move the tool
in the leftward direction slowly.
CAUTION:
Apply light pressure on the tool. Excessive pressure on
the tool will only cause a poor finish and overloading of
the motor.
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and the bat-
tery cartridge is removed before attempting to perform
inspection or maintenance.
Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Replacing carbon brushes
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep
the carbon brushes clean and free to slip in the holders.
Both carbon brushes should be replaced at the same
time. Use only identical carbon brushes. (Fig. 8)
Insert the top end of slotted bit screwdriver into the notch
in the tool and remove the holder cap cover by lifting it
up. (Fig. 9)
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps. (Fig. 10)
Reinstall the holder cap cover on the tool.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
OPTIONAL ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
Side handle (accessory) (Fig. 11, 12, 13 & 14)
When using the side handle, remove the rubber protec-
tor, insert the side handle on the tool barrel as far as it
will go and rotate it to the desired angle. Then tighten the
handle firmly by turning clockwise.
CAUTION:
When using the tool without handle, always install the
rubber protector on the tool.
When installing the rubber protector, always push it
onto the tool so that the top round recessed shape of
the rubber is positioned near the switch position.
Wheel points
Collet cone (3 mm, 6 mm, 8 mm, 1/4", 1/8")
•Collet nut
Wrench 13
Side handle set
Makita genuine battery and charger
NOTE:
Some items in the list may be included in the tool pack-
age as standard accessories. They may differ from
country to country.
ENG905-1
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
pA
): 72 dB (A)
Uncertainty (K): 3 dB (A)
The noise level under working may exceed 80 dB (A).
Wear ear protection
ENG900-1
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Model DGD800
Work mode: surface grinding
Vibration emission (a
h, SG
): 6.5 m/s
2
Uncertainty (K): 1.5 m/s
2
Model DGD801
Work mode: surface grinding
Vibration emission (a
h, SG
): 2.5 m/s
2
or less
Uncertainty (K): 1.5 m/s
2
ENG901-1
The declared vibration emission value has been mea-
sured in accordance with the standard test method and
may be used for comparing one tool with another.
The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
Be sure to identify safety measures to protect the oper-
ator that are based on an estimation of exposure in the
actual conditions of use (taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to
the trigger time).
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DGD801 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DGD801 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info