Manual Makita DGA464 (page 16 of 188) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691747

Zoom out

Zoom in

1/188

16 ENGLISH

Overdischarge protection

When the battery capacity is not enough, the tool stops

automatically. In this case, remove the battery from the

tool and charge the battery.

Releasing protection lock

When the protection system works repeatedly, the tool is

locked and the battery indicator shows the following state.

In this situation, the tool does not start even if turning

the tool off and on. To release the protection lock,

remove the battery, set it to the battery charger and wait

until the charging nishes.

Off

Blinking

Shaft lock

Press the shaft lock to prevent spindle rotation when

installing or removing accessories.

► Fig.4: 1. Shaft lock

NOTICE: Never actuate the shaft lock when the

spindle is moving. The tool may be damaged.

Switch action

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

slide switch actuates properly and returns to the

"OFF" position when the rear of the slide switch

is depressed.

CAUTION: Switch can be locked in "ON" posi-

tion for ease of operator comfort during extended

use. Apply caution when locking tool in "ON"

position and maintain rm grasp on tool.

To start the tool, slide the slide switch toward the “I

(ON)” position by pushing the rear of the slide switch.

For continuous operation, press the front of the slide

switch to lock it.

To stop the tool, press the rear of the slide switch, then

slide it toward the “O (OFF)” position.

► Fig.5: 1. Slide switch

Speed adjusting dial

The rotation speed of the tool can be changed by turning

the speed adjusting dial. The table below shows the num-

ber on the dial and the corresponding rotation speed.

► Fig.6: 1. Speed adjusting dial

Number Speed

1 3,000 min

-1

2 4,500 min

-1

3 6,000 min

-1

4 7,500 min

-1

5 8,500 min

-1

NOTICE: If the tool is operated continuously at

low speed for a long time, the motor will get over-

loaded, resulting in tool malfunction.

NOTICE: When changing the speed dial from "5"

to "1", turn the dial counterclockwise. Do not turn

the dial clockwise forcibly.

Automatic speed change function

► Fig.7: 1. Mode indicator

Mode indicator status Operation mode

High speed mode

High torque mode

This tool has "high speed mode" and "high torque

mode". It automatically changes operation mode

depending on the work load. When mode indicator

lights up during operation, the tool is in high torque

mode.

Accidental re-start preventive

function

Even if the battery cartridge is installed on the tool with

the slide switch in the "I (ON)" position, the tool does

not start.

To start the tool, rst slide the slide switch toward the

"O (OFF)" position and then slide it toward the "I (ON)"

position.

Electronic torque control function

The tool electronically detects situations where the

wheel or accessory may be at risk to be bound. In the

situation, the tool is automatically shut off to prevent

further rotation of the spindle (it does not prevent

kickback).

To restart the tool, switch off the tool rst, remove the

cause of sudden drop in the rotation speed, and then

turn the tool on.

Soft start feature

Soft start feature reduces starting reaction.

Electric brake

For model DGA413/DGA414/DGA463/DGA464/

DGA513/DGA514 only

Electric brake is activated after the tool is switched off.

The brake does not work when the power supply is shut

down, such as the battery is removed accidentally, with

the switch still on.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DGA464 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 33,04 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DGA464 Manual

Product: