Manual Makita DFT087FMZ (page 9 of 84) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

793615

Zoom out

Zoom in

1/84

9ENGLISH

Adjusting the fastening torque

When you wish to drive machine screws, hex bolts,

etc. with the predetermined torque, adjust the fastening

torque as follows.

CAUTION: When adjusting the fastening

torque, remove the battery cartridge (excluding

the process of working with the battery cartridge

attached).

1. Open the change plate by hand so that you can

see a hole.

Fig.7: 1. Change plate

2. Pull the switch trigger and release it so that the

adjust ring rotates and the hole becomes visible. And

then remove the battery cartridge.

3. Use an optional adjust grip to adjust the fastening

torque. Insert the pin of the adjust grip into the hole

in the front of the tool. And then, turn the adjust grip

clockwise to set a greater fastening torque, and coun-

terclockwise to set a smaller fastening torque.

Fig.8: 1. Adjust grip 2. Hole for adjust grip

4. Insert the battery cartridge and be sure that a

fastening torque has been set up by using a fastening

torque tester.

CAUTION: Remove the adjust grip before

turning on the power of the tool.

5. Close the change plate by hand securely.

Adjusting no-load speed and

revolution angle etc.

You can adjust the no-load speed, number of turn, etc.

of the tool with your computer. Install the application

software in your computer and connect it to the tool with

an USB cable.

Fig.9: 1. USB port 2. USB cover 3. USB cable

NOTICE: Make sure that the USB cover closed

when fastening.

NOTE: Use the Makita genuine USB cable to con-

nect your computer to the tool. Refer to the section

"SPECIFICATIONS".

NOTE: For the application software, please contact

Makita sales representative.

ASSEMBLY

CAUTION: Always be sure that the tool is

󰀨

before carrying out any work on the tool.

Installing or removing driver bit/socket bit

Fig.10

Use only driver bit/socket bit that has inserting portion



socket bit.

For tool with shallow driver bit hole

A=12mm

B=9mm

Use only these type of driver

bit. Follow the procedure

1. (Note) Bit-piece is not

necessary.

For tool with deep driver bit hole

A=17mm

B=14mm

To install these types of driver

bits, follow the procedure 1.

A=12mm

B=9mm

To install these types of driver

bits, follow the procedure 2.

(Note) Bit-piece is necessary

for installing the bit.

Procedure 1

For tool without one-touch type sleeve

Fig.11: 1. Driver bit 2. Sleeve

To install the driver bit, pull the sleeve in the direction of the

arrow and insert the driver bit into the sleeve as far as it will go.

Then release the sleeve to secure the driver bit.

For tool with one-touch type sleeve

To install the driver bit, insert the driver bit into the

sleeve as far as it will go.

Procedure 2

In addition to Procedure 1, insert the bit-piece into the

sleeve with its pointed end facing in.

Fig.12: 1. Driver bit 2. Bit-piece 3. Sleeve

To remove the driver bit, pull the sleeve in the direction

of the arrow and pull the driver bit out.

NOTE: If the driver bit is not inserted deep enough

into the sleeve, the sleeve will not return to its original

position and the driver bit will not be secured. In this

case, try re-inserting the bit according to the instruc-

tions above.

NOTE:󰀩

the sleeve and insert it into the sleeve as far as it will

go.

NOTE: After inserting the driver bit, make sure that it



Installing hook

Optional accessory

The hook is useful to hang the tool. Install the hook to

the holes on the tool body.

Fig.13: 1. Hook 2. Hole

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DFT087FMZ in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 12.84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DFT087FMZ Manual

Product: