Manual Makita DFT085F (page 7 of 68) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691722

Zoom out

Zoom in

1/68

7 ENGLISH

Reversing switch action

► Fig.5: 1. Reversing switch lever

CAUTION: Always check the direction of

rotation before operation.

CAUTION:

Use the reversing switch only after

the tool comes to a complete stop. Changing the direc-

tion of rotation before the tool stops may damage the tool.

CAUTION:

When not operating the tool, always

set the reversing switch lever to the neutral position.

This tool has a reversing switch to change the direction

of rotation. Depress the reversing switch lever from the

A side for clockwise rotation or from the B side for coun-

terclockwise rotation.

When the reversing switch lever is in the neutral posi-

tion, the switch trigger cannot be pulled.

LED indicator / Beeper

► Fig.6: 1. LED indicator

LED indicator / Beeper on the tool shows the following

functions.

Function Status of the tool Status of the LED indicator/beeper Action to be taken

LED indicator Beeper

Auto-stop with fastening

completion

The preset fasten-

ing torque has been

achieved and the tool

has stopped.

Lights up in green for

approximately one

second.

– –

Alarm against insuf-

cient fastening

The preset fastening

torque has not been

achieved, because

the switch trigger has

released before complet-

ing the fastening.

Lights up in red. A long beep Retighten the screw.

Alarm for low battery

capacity

The battery power

became low and it is

time to replace the

battery cartridge.

Flickers in red slowly. A series of long beeps Replace the battery with

fully charged one.

Auto-stop with low

remaining battery

capacity

The battery power is

almost used up and the

tool stopped.

Lights up in red. A long beep Replace the battery with

fully charged one.

Check of the LED indi-

cator, light and beeper

operation

When the battery

cartridge is installed,

the tool checks for its

LED indicator, light and

beeper.

Lights up rst in green,

next red.

(And then the light

comes on.)

A series of very short

beeps

–

Anti-reset of controller The battery voltage

dropped abnormally for

some reason, and the

tool stopped.

Flickers in red and green

alternatively.

A series of short beeps Replace the battery with

fully charged one.

Overheat protection Tool's controller heated

up abnormaly and the

tool stopped.

Flickers in red quickly. A series of short beeps Remove the battery car-

tridge immediately and

cool the tool down.

Detection of switch

trigger operation when

installing battery

When the battery car-

tridge is installed with

the switch trigger pulled,

the tool stops to avoid

unintentional start.

Flickers in red and green

alternatively.

A series of short beeps Release the switch

trigger.

Motor failure detection Motor failure has been

detected. At this time,

tool does not work.

Flickers in red and green

alternatively.

A series of short beeps Ask your local Makita

Service Center for repair.

Double-hitting detection

When the operator

starts to re-fasten an

already-fastened screw,

the tool detect it and stops.

Lights up in red. A long beep –

Maintenance alarm A maintenance time has

come according to your

preset number of screws

driven.

Flickers in yellow. – Reset the alarm with the

application software.

Alarm for unavailable

data communication

(with the tool in connec-

tion with PC)

Data cannot be

exchanged between the

tool and PC in spite of

the connection.

Flickers in yellow. – Restart the application

software and re-connect

the USB cable.

Indication that data com-

munication is available

(with the tool in connec-

tion with PC)

The tool is connected to

PC and data communi-

cation is available.

Flickers in green. – –

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DFT085F in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 9,1 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DFT085F Manual

Product: