691711
6
Zoom out
Zoom in
Previous page
1/60
Next page
6
Lighting up the lamps (Fig. 5)
CAUTION:
Do not look in the light or see the source of light
directly.
Pull the switch trigger to light up the lamp. The lamp
keeps on lighting while the switch trigger is being pulled.
The light automatically goes out 10 seconds after the
switch trigger is released.
NOTE:
Use a dry cloth to wipe the dirt off the lens of lamp. Be
careful not to scratch the lens of lamp, or it may lower
the illumination.
LED indicator (Fig. 6)
The LED indicator on the tool shows the following functions.
013073
Function Status
Status of the LED indicator/beeper
Action to be
taken
LED indicator Beeper
Auto-stop fastening
This function works when the tool has
reached the preset fastening torque
and normal tightening has been
completed. This helps overtightening
to be avoided.
Lights up in
green for
approximately
one second.
——
Delayed re-start
For approximately one second after
auto-stop fastening, the tool does not
start even if the switch trigger is
pulled.
Warning against
insufficient fastening
Insufficient fastening has been
performed when the switch trigger
has released before reaching the
preset fastening torque.
Lights up in red. A long beep
Retighten the
screw.
Warning for battery
cartridge capacity
This indicates the appropriate time to
replace the battery cartridge when
the battery power becomes low.
Flickers in red
slowly.
A series of long
beeps
Replace the
battery with fully
charged one.
Checking the
remaining battery
capacity, Autostop
This function works when the battery
power is almost used up. At this time,
tool stops immediately.
Lights up in red. A long beep
Replace the
battery with fully
charged one.
Check the LED
indicator, lamp and
beeper operation
This function works to check the
proper operation of the LED indicator,
lamp and beeper when a battery
cartridge has been inserted into the
tool.
Lights up first in
green, next red.
(And then the
lamp comes
on.)
A series of very
short beeps
Anti-reset of
controller
This function works when an
abnormal drop of the battery voltage
occurs for some reason, and the tool
stops.
Flickers in red
and green
alternatively.
A series of short
beeps
Replace the
battery with fully
charged one.
Overheat
This function works when the
temperature of the controller goes up
very highly, and the tool stops.
Flickers in red
quickly.
A series of short
beeps
Remove the
battery cartridge
immediately and
cool the tool
down.
Operation error of
the switch trigger
This function works to avoid the tool’s
immediate start upon insertion of
battery cartridge into the tool with the
switch trigger being pulled.
Flickers in red
and green
alternatively.
A series of short
beeps
Release the
switch trigger.
Warning for limit of
the fastening
capacity
The tool automatically stops without
the clutch working when exceeding
the fastening capacity limit.
Flick
ers in red
and green
alternatively.
A series of short
beeps
Remove the
battery cartridge
and then install
it again.
Be sure to use
the tool under
load within its
capacity.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DFT044F at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DFT044F in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info