Manual Makita DF 010D (page 6 of 52) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

448351

Zoom out

Zoom in

1/52

Guideline for clutch auto-stop

Lighting up the front lamp (Fig. 6 & 7)

CAUTION:

• Do not look in the light or see the source of light

directly.

To turn on the light, slide the lamp switch to the A position.

To turn off the light, slide the lamp switch to the B position.

Even if you leave the lamp on, the light will automatically

turn off after 5 minutes.

Checking the remaining battery capacity,

auto-stop

The lamp signals by flickering when the battery power is

almost used up during use.

At this time, recharge the battery or replace the battery

with a fully charged one.

ASSEMBLY

CAUTION:

• Always be sure that the lock button is in the locked

position B and the battery cartridge is removed before

carrying out any work on the tool.

Installing or removing driver bit or socket

bit (Fig. 8)

Use only the driver bit or socket bit shown in the figure.

Do not use any other driver bit or socket bit.

For European and North & South American countries,

Australia and New Zealand

For other countries

1. To install the bit, pull the sleeve in the direction of the

arrow and insert the bit into the sleeve as far as it will

go. Then release the sleeve to secure the bit. (Fig. 9)

2. To install the bit, pull the sleeve in the direction of the

arrow and insert the bit-piece and bit into the sleeve

as far as it will go. The bit-piece should be inserted

into the sleeve with its pointed end facing in. Then

release the sleeve to secure the bit. (Fig. 10)

To remove the bit, pull the sleeve in the direction of the

arrow and pull the bit out firmly.

NOTE:

• If the bit is not inserted deep enough into the sleeve,

the sleeve will not return to its original position and the

bit will not be secured. In this case, try re-inserting the

bit according to the instructions above.

OPERATION

The tool can be used in two ways; a straight type and a

pistol type which is selectable according to the conditions

of workplace and screwdriving. (Fig. 11)

Screwdriving operation (Fig. 12)

CAUTION:

• Adjust the adjusting ring to the proper torque level for

your work.

Place the point of the driver bit in the screw head and

apply pressure to the tool. Then switch the tool on. When

the clutch cuts in, the motor will stop automatically. Then

release the switch.

CAUTION:

• Make sure that the driver bit is inserted straight in the

screw head, or the screw and/or bit may be damaged.

NOTE:

• When driving wood screws, predrill pilot holes to make

driving easier and to prevent splitting of the workpiece.

See the chart.

Work range of

clutch auto-stop

Increments on

adjusting ring

for fastening

torque

Fastening torque

High

speed

Low

speed

Clutch auto-

stop works

Approx. 0.3 N·m

(Approx. 3 Kgf-cm)

Approx. 0.82 N·m

(Approx. 8.4 Kgf-cm)

Approx. 1.35 N·m

(Approx. 13.8 Kgf-cm)

Approx. 1.88 N·m

(Approx. 19.2 Kgf-cm)

Approx. 2.41 N·m

(Approx. 24.6 Kgf-cm)

Approx. 2.9 N·m

(Approx. 30 Kgf-cm)

Clutch auto-

stop does not

work

Low speed

Approx. 5 N·m

(Approx. 49 Kgf-cm)

High speed

Approx. 1.5 N·m

(Approx. 14.7 Kgf-cm)

When driving

machine

screws

Increments

Guideline for machine

screw diameter

1 - 3 2.5 mm

4 - 8 3 mm

9 - 18 4 mm

19 - 21 5 mm

A=12mm

B=9mm

Use only these type of bit. Follow the

procedure (1).

(Note) Bit-piece is not necessary.

A=17 mm

B=14 mm

To install these types of bits, follow the

procedure (1).

(Note) Makita bits are these types.

A=12 mm

B=9 mm

To install these types of bits, follow the

procedure (2).

(Note) Bit-piece is necessary for installing

the bit.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DF 010D in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DF 010D Manual

Product: