Manual Makita DDF485RFJ (page 7 of 15) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

711019

Zoom out

Zoom in

1/15

7 ENGLISH

Reversing switch action

►Fig.5: 1. Reversing switch lever

CAUTION: Always check the direction of

rotation before operation.

CAUTION: Use the reversing switch only after

the tool comes to a complete stop. Changing the

directionofrotationbeforethetoolstopsmaydam-

age the tool.

CAUTION: When not operating the tool,

always set the reversing switch lever to the neu-

tral position.

This tool has a reversing switch to change the direction

of rotation. Depress the reversing switch lever from the

AsideforclockwiserotationorfromtheBsideforcoun-

terclockwise rotation.

When the reversing switch lever is in the neutral posi-

tion,theswitchtriggercannotbepulled.

Speed change

►Fig.6: 1. Speed change lever

CAUTION:

Always set the speed change lever

fully to the correct position.Ifyouoperatethetoolwith

thespeedchangeleverpositionedhalfwaybetweenthe

"1"sideand"2"side,thetoolmaybedamaged.

CAUTION: Do not use the speed change lever

while the tool is running.Thetoolmaybedamaged.

Displayed

Number

Speed Torque Applicable

operation

1 Low High Heavyload-

ing operation

2 High Low Light loading

operation

Tochangethespeed,switchoffthetoolrst.Pushthe

speedchangelevertodisplay"2"forhighspeedor"1"for

lowspeedbuthightorque.Besurethatthespeedchange

leverissettothecorrectpositionbeforeoperation.

Ifthetoolspeediscomingdownextremelyduringtheoperationwith

display"2",pushthelevertodisplay"1"andrestarttheoperation.

Adjusting the fastening torque

►Fig.7: 1.Adjustingring2. Graduation 3.Arrow

Thefasteningtorquecanbeadjustedin22levelsbyturningtheadjustingring.Alignthegraduationswiththearrow

onthetoolbody.Youcangettheminimumfasteningtorqueat1andmaximumtorqueat

marking.

Theclutchwillslipatvarioustorquelevelswhensetatthenumber1to21.Theclutchdoesnotworkatthe marking.

Beforeactualoperation,driveatrialscrewintoyourmaterialorapieceofduplicatematerialtodeterminewhich

torque level is required for a particular application.

Thefollowingshowstheroughguideoftherelationshipbetweenthescrewsizeandgraduation.

Graduation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Machine screw M4 M5 M6

Wood

screw

Soft wood

(e.g. pine)

– ɸ3.5 x 22 ɸ4.1x 38 –

Hard wood

(e.g. lauan)

– ɸ3.5 x 22 ɸ4.1x 38 –

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Installing or removing driver bit/

drill bit

►Fig.8: 1. Sleeve 2. Close 3. Open

Turn the sleeve counterclockwise to open the chuck

jaws.Placethedriverbit/drillbitinthechuckasfar

as it will go. Turn the sleeve clockwise to tighten the

chuck.Toremovethedriverbit/drillbit,turnthesleeve

counterclockwise.

Installing hook

CAUTION:

When installing the hook, always

secure it with the screw rmly.Ifnot,thehookmay

comeofffromthetoolandresultinthepersonalinjury.

►Fig.9: 1. Groove 2. Hook 3. Screw

Thehookisconvenientfortemporarilyhangingthetool.Thiscan

beinstalledoneithersideofthetool.Toinstallthehook,insertit

into a groove in the tool housing on either side and then secure it

with a screw. To remove, loosen the screw and then take it out.

Installing driver bit holder

Optional accessory

►Fig.10: 1.Driverbitholder2.Driverbit

Fitthedriverbitholderintotheprotrusionatthetoolfoot

on either right or left side and secure it with a screw.

Whennotusingthedriverbit,keepitinthedriverbit

holders.Driverbits45mm-longcanbekeptthere.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DDF485RFJ in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 3,85 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DDF485RFJ Manual

Product: