Manual Makita DDF484RTJ (page 7 of 68) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

711022

Zoom out

Zoom in

1/68

7 ENGLISH

Switch action

►Fig.4: 1. Switch trigger

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

Tostartthetool,simplypulltheswitchtrigger.Tool

speedisincreasedbyincreasingpressureontheswitch

trigger. Release the switch trigger to stop.

NOTE:Thetoolautomaticallystopsifyoukeeppull-

ingtheswitchtriggerforabout6minutes.

Lighting up the front lamp

►Fig.5: 1. Lamp

CAUTION: Do not look in the light or see the

source of light directly.

Pulltheswitchtriggertolightupthelamp.Thelamp

keepsonlightingwhiletheswitchtriggerisbeingpulled.

Thelampgoesoutapproximately10secondsafter

releasing the switch trigger.

NOTE: When the tool is overheated, the tool stops

automaticallyandthelampstartsashing.Inthis

case,releasetheswitchtrigger.Thelampturnsoffin

one minute.

NOTE: Use a dry cloth to wipe the dirt off the lens of

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

Reversing switch action

►Fig.6: 1. Reversing switch lever

CAUTION: Always check the direction of

rotation before operation.

CAUTION: Use the reversing switch only after

the tool comes to a complete stop. Changing the

directionofrotationbeforethetoolstopsmaydam-

age the tool.

CAUTION: When not operating the tool,

always set the reversing switch lever to the neu-

tral position.

Thistoolhasareversingswitchtochangethedirection

of rotation. Depress the reversing switch lever from the

AsideforclockwiserotationorfromtheBsideforcoun-

terclockwise rotation.

When the reversing switch lever is in the neutral posi-

tion,theswitchtriggercannotbepulled.

Speed change

►Fig.7: 1. Speed change lever

CAUTION: Always set the speed change lever

fully to the correct position. If you operate the

tool with the speed change lever positioned halfway

betweenthe"1"sideand"2"side,thetoolmaybe

damaged.

CAUTION: Do not use the speed change lever

while the tool is running.Thetoolmaybedamaged.

Displayed

Number

Speed Torque Applicable

operation

1 Low High Heavy load-

ing operation

2 High Low Light loading

operation

Tochangethespeed,switchoffthetoolrst.Pushthe

speedchangelevertodisplay"2"forhighspeedor"1"for

lowspeedbuthightorque.Besurethatthespeedchange

leverissettothecorrectpositionbeforeoperation.

If the tool speed is coming down extremely during the

operationwithdisplay"2",pushthelevertodisplay"1"

and restart the operation.

Adjusting the fastening torque

►Fig.8: 1.Adjustingring2. Graduation 3.Arrow

Thefasteningtorquecanbeadjustedin22levelsbyturningtheadjustingring.Alignthegraduationswiththearrow

onthetoolbody.Youcangettheminimumfasteningtorqueat1andmaximumtorqueat

marking.

Theclutchwillslipatvarioustorquelevelswhensetatthenumber1to21.Theclutchdoesnotworkat

the marking.

Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which

torque level is required for a particular application.

Thefollowingshowstheroughguideoftherelationshipbetweenthescrewsizeandgraduation.

Graduation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Machine screw M4 M5 M6

Wood

screw

Soft wood

(e.g. pine)

– ɸ3.5 x 22 ɸ4.1x 38 –

Hard wood

(e.g. lauan)

– ɸ3.5 x 22 ɸ4.1x 38 –

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DDF484RTJ in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 14,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DDF484RTJ Manual

Product: