Manual Makita DDF083 (page 6 of 68) (English, German, Dutch, Danish, French, Italian, Portuguese, Portuguese, Spanish)

657998

Zoom out

Zoom in

1/68

6 ENGLISH

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge.Failuretoholdthetoolandthebattery

cartridgermlymaycausethemtoslipoffyourhands

andresultindamagetothetoolandbatterycartridge

andapersonalinjury.

►Fig.1: 1. Red indicator 2.Button3. Battery cartridge

Toremovethebatterycartridge,slideitfromthetool

whileslidingthebuttononthefrontofthecartridge.

Toinstallthebatterycartridge,alignthetongueonthe

batterycartridgewiththegrooveinthehousingandslip

itintoplace.Insertitallthewayuntilitlocksinplace

withalittleclick.Ifyoucanseetheredindicatoronthe

uppersideofthebutton,itisnotlockedcompletely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen.Ifnot,

itmayaccidentallyfalloutofthetool,causinginjuryto

youorsomeonearoundyou.

CAUTION: Do not install the battery cartridge

forcibly.Ifthecartridgedoesnotslideineasily,itis

notbeinginsertedcorrectly.

Indicating the remaining battery

capacity

Only for battery cartridges with "B" at the end of the

model number

►Fig.2: 1.Indicatorlamps2.Checkbutton

Pressthecheckbuttononthebatterycartridgetoindi-

catetheremainingbatterycapacity.Theindicatorlamps

lightupforfewseconds.

Indicator lamps Remaining

capacity

Lighted Off

75% to 100%

50% to 75%

25% to 50%

0% to 25%

NOTE:Dependingontheconditionsofuseandthe

ambienttemperature,theindicationmaydifferslightly

fromtheactualcapacity.

Tool / battery protection system

Thetoolisequippedwithatool/batteryprotectionsys-

tem.Thissystemautomaticallycutsoffpowertothe

motortoextendtoolandbatterylife.Thetoolwillauto-

maticallystopduringoperationifthetoolorbatteryis

placedunderoneofthefollowingconditions:

Overload protection

Whenthetool/batteryisoperatedinamannerthat

causesittodrawanabnormallyhighcurrent,thetool

automaticallystopswithoutanyindication.Inthissit-

uation,turnthetooloffandstoptheapplicationthat

causedthetooltobecomeoverloaded.Thenturnthe

tool on to restart.

Overheat protection

Whenthetool/batteryisoverheated,thetoolstops

automatically.Inthissituation,letthetool/batterycool

beforeturningthetoolonagain.

Overdischarge protection

Whenthebatterycapacityisnotenough,thetoolstops

automatically.Inthiscase,removethebatteryfromthe

toolandchargethebattery.

NOTE:Overheatprotection(forbattery)willworkonly

withbatterieswithstarmarking.

►Fig.3: 1. Star marking

Switch action

►Fig.4: 1. Switch trigger

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

Tostartthetool,simplypulltheswitchtrigger.Tool

speedisincreasedbyincreasingpressureontheswitch

trigger. Release the switch trigger to stop.

NOTE:Thetoolautomaticallystopsifyoukeeppull-

ingtheswitchtriggerforabout6minutes.

Lighting up the front lamp

►Fig.5: 1. Lamp

CAUTION: Do not look in the light or see the

source of light directly.

Pulltheswitchtriggertolightupthelamp.Thelamp

keepsonlightingwhiletheswitchtriggerisbeingpulled.

Thelampgoesoutapproximately10secondsafter

releasing the switch trigger.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DDF083 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Portuguese, Spanish as an attachment in your email.

The manual is 12,97 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DDF083 Manual

Product: